swh:1:snp:3c665ee4f67729f27f2e40193ab88e7298cf0fef
Tip revision: 319e2e3f63c348a9b66db4667efa73178e18b17d authored by Linus Torvalds on 15 December 2013, 20:31:33 UTC
Linux 3.13-rc4
Linux 3.13-rc4
Tip revision: 319e2e3
modedb.txt
modedb default video mode support
Currently all frame buffer device drivers have their own video mode databases,
which is a mess and a waste of resources. The main idea of modedb is to have
- one routine to probe for video modes, which can be used by all frame buffer
devices
- one generic video mode database with a fair amount of standard videomodes
(taken from XFree86)
- the possibility to supply your own mode database for graphics hardware that
needs non-standard modes, like amifb and Mac frame buffer drivers (which
use macmodes.c)
When a frame buffer device receives a video= option it doesn't know, it should
consider that to be a video mode option. If no frame buffer device is specified
in a video= option, fbmem considers that to be a global video mode option.
Valid mode specifiers (mode_option argument):
<xres>x<yres>[M][R][-<bpp>][@<refresh>][i][m][eDd]
<name>[-<bpp>][@<refresh>]
with <xres>, <yres>, <bpp> and <refresh> decimal numbers and <name> a string.
Things between square brackets are optional.
If 'M' is specified in the mode_option argument (after <yres> and before
<bpp> and <refresh>, if specified) the timings will be calculated using
VESA(TM) Coordinated Video Timings instead of looking up the mode from a table.
If 'R' is specified, do a 'reduced blanking' calculation for digital displays.
If 'i' is specified, calculate for an interlaced mode. And if 'm' is
specified, add margins to the calculation (1.8% of xres rounded down to 8
pixels and 1.8% of yres).
Sample usage: 1024x768M@60m - CVT timing with margins
DRM drivers also add options to enable or disable outputs:
'e' will force the display to be enabled, i.e. it will override the detection
if a display is connected. 'D' will force the display to be enabled and use
digital output. This is useful for outputs that have both analog and digital
signals (e.g. HDMI and DVI-I). For other outputs it behaves like 'e'. If 'd'
is specified the output is disabled.
You can additionally specify which output the options matches to.
To force the VGA output to be enabled and drive a specific mode say:
video=VGA-1:1280x1024@60me
Specifying the option multiple times for different ports is possible, e.g.:
video=LVDS-1:d video=HDMI-1:D
***** oOo ***** oOo ***** oOo ***** oOo ***** oOo ***** oOo ***** oOo *****
What is the VESA(TM) Coordinated Video Timings (CVT)?
From the VESA(TM) Website:
"The purpose of CVT is to provide a method for generating a consistent
and coordinated set of standard formats, display refresh rates, and
timing specifications for computer display products, both those
employing CRTs, and those using other display technologies. The
intention of CVT is to give both source and display manufacturers a
common set of tools to enable new timings to be developed in a
consistent manner that ensures greater compatibility."
This is the third standard approved by VESA(TM) concerning video timings. The
first was the Discrete Video Timings (DVT) which is a collection of
pre-defined modes approved by VESA(TM). The second is the Generalized Timing
Formula (GTF) which is an algorithm to calculate the timings, given the
pixelclock, the horizontal sync frequency, or the vertical refresh rate.
The GTF is limited by the fact that it is designed mainly for CRT displays.
It artificially increases the pixelclock because of its high blanking
requirement. This is inappropriate for digital display interface with its high
data rate which requires that it conserves the pixelclock as much as possible.
Also, GTF does not take into account the aspect ratio of the display.
The CVT addresses these limitations. If used with CRT's, the formula used
is a derivation of GTF with a few modifications. If used with digital
displays, the "reduced blanking" calculation can be used.
From the framebuffer subsystem perspective, new formats need not be added
to the global mode database whenever a new mode is released by display
manufacturers. Specifying for CVT will work for most, if not all, relatively
new CRT displays and probably with most flatpanels, if 'reduced blanking'
calculation is specified. (The CVT compatibility of the display can be
determined from its EDID. The version 1.3 of the EDID has extra 128-byte
blocks where additional timing information is placed. As of this time, there
is no support yet in the layer to parse this additional blocks.)
CVT also introduced a new naming convention (should be seen from dmesg output):
<pix>M<a>[-R]
where: pix = total amount of pixels in MB (xres x yres)
M = always present
a = aspect ratio (3 - 4:3; 4 - 5:4; 9 - 15:9, 16:9; A - 16:10)
-R = reduced blanking
example: .48M3-R - 800x600 with reduced blanking
Note: VESA(TM) has restrictions on what is a standard CVT timing:
- aspect ratio can only be one of the above values
- acceptable refresh rates are 50, 60, 70 or 85 Hz only
- if reduced blanking, the refresh rate must be at 60Hz
If one of the above are not satisfied, the kernel will print a warning but the
timings will still be calculated.
***** oOo ***** oOo ***** oOo ***** oOo ***** oOo ***** oOo ***** oOo *****
To find a suitable video mode, you just call
int __init fb_find_mode(struct fb_var_screeninfo *var,
struct fb_info *info, const char *mode_option,
const struct fb_videomode *db, unsigned int dbsize,
const struct fb_videomode *default_mode,
unsigned int default_bpp)
with db/dbsize your non-standard video mode database, or NULL to use the
standard video mode database.
fb_find_mode() first tries the specified video mode (or any mode that matches,
e.g. there can be multiple 640x480 modes, each of them is tried). If that
fails, the default mode is tried. If that fails, it walks over all modes.
To specify a video mode at bootup, use the following boot options:
video=<driver>:<xres>x<yres>[-<bpp>][@refresh]
where <driver> is a name from the table below. Valid default modes can be
found in linux/drivers/video/modedb.c. Check your driver's documentation.
There may be more modes.
Drivers that support modedb boot options
Boot Name Cards Supported
amifb - Amiga chipset frame buffer
aty128fb - ATI Rage128 / Pro frame buffer
atyfb - ATI Mach64 frame buffer
pm2fb - Permedia 2/2V frame buffer
pm3fb - Permedia 3 frame buffer
sstfb - Voodoo 1/2 (SST1) chipset frame buffer
tdfxfb - 3D Fx frame buffer
tridentfb - Trident (Cyber)blade chipset frame buffer
vt8623fb - VIA 8623 frame buffer
BTW, only a few fb drivers use this at the moment. Others are to follow
(feel free to send patches). The DRM drivers also support this.