swh:1:snp:3c665ee4f67729f27f2e40193ab88e7298cf0fef
Tip revision: 3cea11cd5e3b00d91caf0b4730194039b45c5891 authored by Linus Torvalds on 01 November 2020, 22:43:51 UTC
Linux 5.10-rc2
Linux 5.10-rc2
Tip revision: 3cea11c
mca.rst
=============================================================
An ad-hoc collection of notes on IA64 MCA and INIT processing
=============================================================
Feel free to update it with notes about any area that is not clear.
---
MCA/INIT are completely asynchronous. They can occur at any time, when
the OS is in any state. Including when one of the cpus is already
holding a spinlock. Trying to get any lock from MCA/INIT state is
asking for deadlock. Also the state of structures that are protected
by locks is indeterminate, including linked lists.
---
The complicated ia64 MCA process. All of this is mandated by Intel's
specification for ia64 SAL, error recovery and unwind, it is not as
if we have a choice here.
* MCA occurs on one cpu, usually due to a double bit memory error.
This is the monarch cpu.
* SAL sends an MCA rendezvous interrupt (which is a normal interrupt)
to all the other cpus, the slaves.
* Slave cpus that receive the MCA interrupt call down into SAL, they
end up spinning disabled while the MCA is being serviced.
* If any slave cpu was already spinning disabled when the MCA occurred
then it cannot service the MCA interrupt. SAL waits ~20 seconds then
sends an unmaskable INIT event to the slave cpus that have not
already rendezvoused.
* Because MCA/INIT can be delivered at any time, including when the cpu
is down in PAL in physical mode, the registers at the time of the
event are _completely_ undefined. In particular the MCA/INIT
handlers cannot rely on the thread pointer, PAL physical mode can
(and does) modify TP. It is allowed to do that as long as it resets
TP on return. However MCA/INIT events expose us to these PAL
internal TP changes. Hence curr_task().
* If an MCA/INIT event occurs while the kernel was running (not user
space) and the kernel has called PAL then the MCA/INIT handler cannot
assume that the kernel stack is in a fit state to be used. Mainly
because PAL may or may not maintain the stack pointer internally.
Because the MCA/INIT handlers cannot trust the kernel stack, they
have to use their own, per-cpu stacks. The MCA/INIT stacks are
preformatted with just enough task state to let the relevant handlers
do their job.
* Unlike most other architectures, the ia64 struct task is embedded in
the kernel stack[1]. So switching to a new kernel stack means that
we switch to a new task as well. Because various bits of the kernel
assume that current points into the struct task, switching to a new
stack also means a new value for current.
* Once all slaves have rendezvoused and are spinning disabled, the
monarch is entered. The monarch now tries to diagnose the problem
and decide if it can recover or not.
* Part of the monarch's job is to look at the state of all the other
tasks. The only way to do that on ia64 is to call the unwinder,
as mandated by Intel.
* The starting point for the unwind depends on whether a task is
running or not. That is, whether it is on a cpu or is blocked. The
monarch has to determine whether or not a task is on a cpu before it
knows how to start unwinding it. The tasks that received an MCA or
INIT event are no longer running, they have been converted to blocked
tasks. But (and its a big but), the cpus that received the MCA
rendezvous interrupt are still running on their normal kernel stacks!
* To distinguish between these two cases, the monarch must know which
tasks are on a cpu and which are not. Hence each slave cpu that
switches to an MCA/INIT stack, registers its new stack using
set_curr_task(), so the monarch can tell that the _original_ task is
no longer running on that cpu. That gives us a decent chance of
getting a valid backtrace of the _original_ task.
* MCA/INIT can be nested, to a depth of 2 on any cpu. In the case of a
nested error, we want diagnostics on the MCA/INIT handler that
failed, not on the task that was originally running. Again this
requires set_curr_task() so the MCA/INIT handlers can register their
own stack as running on that cpu. Then a recursive error gets a
trace of the failing handler's "task".
[1]
My (Keith Owens) original design called for ia64 to separate its
struct task and the kernel stacks. Then the MCA/INIT data would be
chained stacks like i386 interrupt stacks. But that required
radical surgery on the rest of ia64, plus extra hard wired TLB
entries with its associated performance degradation. David
Mosberger vetoed that approach. Which meant that separate kernel
stacks meant separate "tasks" for the MCA/INIT handlers.
---
INIT is less complicated than MCA. Pressing the nmi button or using
the equivalent command on the management console sends INIT to all
cpus. SAL picks one of the cpus as the monarch and the rest are
slaves. All the OS INIT handlers are entered at approximately the same
time. The OS monarch prints the state of all tasks and returns, after
which the slaves return and the system resumes.
At least that is what is supposed to happen. Alas there are broken
versions of SAL out there. Some drive all the cpus as monarchs. Some
drive them all as slaves. Some drive one cpu as monarch, wait for that
cpu to return from the OS then drive the rest as slaves. Some versions
of SAL cannot even cope with returning from the OS, they spin inside
SAL on resume. The OS INIT code has workarounds for some of these
broken SAL symptoms, but some simply cannot be fixed from the OS side.
---
The scheduler hooks used by ia64 (curr_task, set_curr_task) are layer
violations. Unfortunately MCA/INIT start off as massive layer
violations (can occur at _any_ time) and they build from there.
At least ia64 makes an attempt at recovering from hardware errors, but
it is a difficult problem because of the asynchronous nature of these
errors. When processing an unmaskable interrupt we sometimes need
special code to cope with our inability to take any locks.
---
How is ia64 MCA/INIT different from x86 NMI?
* x86 NMI typically gets delivered to one cpu. MCA/INIT gets sent to
all cpus.
* x86 NMI cannot be nested. MCA/INIT can be nested, to a depth of 2
per cpu.
* x86 has a separate struct task which points to one of multiple kernel
stacks. ia64 has the struct task embedded in the single kernel
stack, so switching stack means switching task.
* x86 does not call the BIOS so the NMI handler does not have to worry
about any registers having changed. MCA/INIT can occur while the cpu
is in PAL in physical mode, with undefined registers and an undefined
kernel stack.
* i386 backtrace is not very sensitive to whether a process is running
or not. ia64 unwind is very, very sensitive to whether a process is
running or not.
---
What happens when MCA/INIT is delivered what a cpu is running user
space code?
The user mode registers are stored in the RSE area of the MCA/INIT on
entry to the OS and are restored from there on return to SAL, so user
mode registers are preserved across a recoverable MCA/INIT. Since the
OS has no idea what unwind data is available for the user space stack,
MCA/INIT never tries to backtrace user space. Which means that the OS
does not bother making the user space process look like a blocked task,
i.e. the OS does not copy pt_regs and switch_stack to the user space
stack. Also the OS has no idea how big the user space RSE and memory
stacks are, which makes it too risky to copy the saved state to a user
mode stack.
---
How do we get a backtrace on the tasks that were running when MCA/INIT
was delivered?
mca.c:::ia64_mca_modify_original_stack(). That identifies and
verifies the original kernel stack, copies the dirty registers from
the MCA/INIT stack's RSE to the original stack's RSE, copies the
skeleton struct pt_regs and switch_stack to the original stack, fills
in the skeleton structures from the PAL minstate area and updates the
original stack's thread.ksp. That makes the original stack look
exactly like any other blocked task, i.e. it now appears to be
sleeping. To get a backtrace, just start with thread.ksp for the
original task and unwind like any other sleeping task.
---
How do we identify the tasks that were running when MCA/INIT was
delivered?
If the previous task has been verified and converted to a blocked
state, then sos->prev_task on the MCA/INIT stack is updated to point to
the previous task. You can look at that field in dumps or debuggers.
To help distinguish between the handler and the original tasks,
handlers have _TIF_MCA_INIT set in thread_info.flags.
The sos data is always in the MCA/INIT handler stack, at offset
MCA_SOS_OFFSET. You can get that value from mca_asm.h or calculate it
as KERNEL_STACK_SIZE - sizeof(struct pt_regs) - sizeof(struct
ia64_sal_os_state), with 16 byte alignment for all structures.
Also the comm field of the MCA/INIT task is modified to include the pid
of the original task, for humans to use. For example, a comm field of
'MCA 12159' means that pid 12159 was running when the MCA was
delivered.