swh:1:snp:3c665ee4f67729f27f2e40193ab88e7298cf0fef
Tip revision: 6bf4ca7fbc85d80446ac01c0d1d77db4d91a6d84 authored by Greg Kroah-Hartman on 23 September 2018, 17:15:18 UTC
Linux 4.19-rc5
Linux 4.19-rc5
Tip revision: 6bf4ca7
zorro.txt
========================================
Writing Device Drivers for Zorro Devices
========================================
:Author: Written by Geert Uytterhoeven <geert@linux-m68k.org>
:Last revised: September 5, 2003
Introduction
------------
The Zorro bus is the bus used in the Amiga family of computers. Thanks to
AutoConfig(tm), it's 100% Plug-and-Play.
There are two types of Zorro buses, Zorro II and Zorro III:
- The Zorro II address space is 24-bit and lies within the first 16 MB of the
Amiga's address map.
- Zorro III is a 32-bit extension of Zorro II, which is backwards compatible
with Zorro II. The Zorro III address space lies outside the first 16 MB.
Probing for Zorro Devices
-------------------------
Zorro devices are found by calling ``zorro_find_device()``, which returns a
pointer to the ``next`` Zorro device with the specified Zorro ID. A probe loop
for the board with Zorro ID ``ZORRO_PROD_xxx`` looks like::
struct zorro_dev *z = NULL;
while ((z = zorro_find_device(ZORRO_PROD_xxx, z))) {
if (!zorro_request_region(z->resource.start+MY_START, MY_SIZE,
"My explanation"))
...
}
``ZORRO_WILDCARD`` acts as a wildcard and finds any Zorro device. If your driver
supports different types of boards, you can use a construct like::
struct zorro_dev *z = NULL;
while ((z = zorro_find_device(ZORRO_WILDCARD, z))) {
if (z->id != ZORRO_PROD_xxx1 && z->id != ZORRO_PROD_xxx2 && ...)
continue;
if (!zorro_request_region(z->resource.start+MY_START, MY_SIZE,
"My explanation"))
...
}
Zorro Resources
---------------
Before you can access a Zorro device's registers, you have to make sure it's
not yet in use. This is done using the I/O memory space resource management
functions::
request_mem_region()
release_mem_region()
Shortcuts to claim the whole device's address space are provided as well::
zorro_request_device
zorro_release_device
Accessing the Zorro Address Space
---------------------------------
The address regions in the Zorro device resources are Zorro bus address
regions. Due to the identity bus-physical address mapping on the Zorro bus,
they are CPU physical addresses as well.
The treatment of these regions depends on the type of Zorro space:
- Zorro II address space is always mapped and does not have to be mapped
explicitly using z_ioremap().
Conversion from bus/physical Zorro II addresses to kernel virtual addresses
and vice versa is done using::
virt_addr = ZTWO_VADDR(bus_addr);
bus_addr = ZTWO_PADDR(virt_addr);
- Zorro III address space must be mapped explicitly using z_ioremap() first
before it can be accessed::
virt_addr = z_ioremap(bus_addr, size);
...
z_iounmap(virt_addr);
References
----------
#. linux/include/linux/zorro.h
#. linux/include/uapi/linux/zorro.h
#. linux/include/uapi/linux/zorro_ids.h
#. linux/arch/m68k/include/asm/zorro.h
#. linux/drivers/zorro
#. /proc/bus/zorro