swh:1:snp:3c665ee4f67729f27f2e40193ab88e7298cf0fef
Tip revision: d434405aaab7d0ebc516b68a8fc4100922d7f5ef authored by Linus Torvalds on 11 April 2021, 22:16:13 UTC
Linux 5.12-rc7
Linux 5.12-rc7
Tip revision: d434405
timer.c
/*
* linux/arch/arm/mach-omap2/timer.c
*
* OMAP2 GP timer support.
*
* Copyright (C) 2009 Nokia Corporation
*
* Update to use new clocksource/clockevent layers
* Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
* Copyright (C) 2007 MontaVista Software, Inc.
*
* Original driver:
* Copyright (C) 2005 Nokia Corporation
* Author: Paul Mundt <paul.mundt@nokia.com>
* Juha Yrjölä <juha.yrjola@nokia.com>
* OMAP Dual-mode timer framework support by Timo Teras
*
* Some parts based off of TI's 24xx code:
*
* Copyright (C) 2004-2009 Texas Instruments, Inc.
*
* Roughly modelled after the OMAP1 MPU timer code.
* Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*/
#include <linux/clk.h>
#include <linux/clocksource.h>
#include "soc.h"
#include "common.h"
#include "control.h"
#include "omap-secure.h"
#define REALTIME_COUNTER_BASE 0x48243200
#define INCREMENTER_NUMERATOR_OFFSET 0x10
#define INCREMENTER_DENUMERATOR_RELOAD_OFFSET 0x14
#define NUMERATOR_DENUMERATOR_MASK 0xfffff000
static unsigned long arch_timer_freq;
void set_cntfreq(void)
{
omap_smc1(OMAP5_DRA7_MON_SET_CNTFRQ_INDEX, arch_timer_freq);
}
/*
* The realtime counter also called master counter, is a free-running
* counter, which is related to real time. It produces the count used
* by the CPU local timer peripherals in the MPU cluster. The timer counts
* at a rate of 6.144 MHz. Because the device operates on different clocks
* in different power modes, the master counter shifts operation between
* clocks, adjusting the increment per clock in hardware accordingly to
* maintain a constant count rate.
*/
static void __init realtime_counter_init(void)
{
void __iomem *base;
static struct clk *sys_clk;
unsigned long rate;
unsigned int reg;
unsigned long long num, den;
base = ioremap(REALTIME_COUNTER_BASE, SZ_32);
if (!base) {
pr_err("%s: ioremap failed\n", __func__);
return;
}
sys_clk = clk_get(NULL, "sys_clkin");
if (IS_ERR(sys_clk)) {
pr_err("%s: failed to get system clock handle\n", __func__);
iounmap(base);
return;
}
rate = clk_get_rate(sys_clk);
if (soc_is_dra7xx()) {
/*
* Errata i856 says the 32.768KHz crystal does not start at
* power on, so the CPU falls back to an emulated 32KHz clock
* based on sysclk / 610 instead. This causes the master counter
* frequency to not be 6.144MHz but at sysclk / 610 * 375 / 2
* (OR sysclk * 75 / 244)
*
* This affects at least the DRA7/AM572x 1.0, 1.1 revisions.
* Of course any board built without a populated 32.768KHz
* crystal would also need this fix even if the CPU is fixed
* later.
*
* Either case can be detected by using the two speedselect bits
* If they are not 0, then the 32.768KHz clock driving the
* coarse counter that corrects the fine counter every time it
* ticks is actually rate/610 rather than 32.768KHz and we
* should compensate to avoid the 570ppm (at 20MHz, much worse
* at other rates) too fast system time.
*/
reg = omap_ctrl_readl(DRA7_CTRL_CORE_BOOTSTRAP);
if (reg & DRA7_SPEEDSELECT_MASK) {
num = 75;
den = 244;
goto sysclk1_based;
}
}
/* Numerator/denumerator values refer TRM Realtime Counter section */
switch (rate) {
case 12000000:
num = 64;
den = 125;
break;
case 13000000:
num = 768;
den = 1625;
break;
case 19200000:
num = 8;
den = 25;
break;
case 20000000:
num = 192;
den = 625;
break;
case 26000000:
num = 384;
den = 1625;
break;
case 27000000:
num = 256;
den = 1125;
break;
case 38400000:
default:
/* Program it for 38.4 MHz */
num = 4;
den = 25;
break;
}
sysclk1_based:
/* Program numerator and denumerator registers */
reg = readl_relaxed(base + INCREMENTER_NUMERATOR_OFFSET) &
NUMERATOR_DENUMERATOR_MASK;
reg |= num;
writel_relaxed(reg, base + INCREMENTER_NUMERATOR_OFFSET);
reg = readl_relaxed(base + INCREMENTER_DENUMERATOR_RELOAD_OFFSET) &
NUMERATOR_DENUMERATOR_MASK;
reg |= den;
writel_relaxed(reg, base + INCREMENTER_DENUMERATOR_RELOAD_OFFSET);
arch_timer_freq = DIV_ROUND_UP_ULL(rate * num, den);
set_cntfreq();
iounmap(base);
}
void __init omap5_realtime_timer_init(void)
{
omap_clk_init();
realtime_counter_init();
timer_probe();
}