swh:1:snp:3c665ee4f67729f27f2e40193ab88e7298cf0fef
Tip revision: c1be5a5b1b355d40e6cf79cc979eb66dafa24ad1 authored by Linus Torvalds on 29 April 2013, 00:36:01 UTC
Linux 3.9
Linux 3.9
Tip revision: c1be5a5
platsmp.c
/*
* Copyright (C) 2002 ARM Ltd.
* Copyright (C) 2008 STMicroelctronics.
* Copyright (C) 2009 ST-Ericsson.
* Author: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
*
* This file is based on arm realview platform
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/smp.h>
#include <linux/io.h>
#include <linux/irqchip/arm-gic.h>
#include <asm/cacheflush.h>
#include <asm/smp_plat.h>
#include <asm/smp_scu.h>
#include <mach/hardware.h>
#include <mach/setup.h>
#include "id.h"
/* This is called from headsmp.S to wakeup the secondary core */
extern void u8500_secondary_startup(void);
/*
* Write pen_release in a way that is guaranteed to be visible to all
* observers, irrespective of whether they're taking part in coherency
* or not. This is necessary for the hotplug code to work reliably.
*/
static void write_pen_release(int val)
{
pen_release = val;
smp_wmb();
__cpuc_flush_dcache_area((void *)&pen_release, sizeof(pen_release));
outer_clean_range(__pa(&pen_release), __pa(&pen_release + 1));
}
static void __iomem *scu_base_addr(void)
{
if (cpu_is_u8500_family() || cpu_is_ux540_family())
return __io_address(U8500_SCU_BASE);
else
ux500_unknown_soc();
return NULL;
}
static DEFINE_SPINLOCK(boot_lock);
static void __cpuinit ux500_secondary_init(unsigned int cpu)
{
/*
* if any interrupts are already enabled for the primary
* core (e.g. timer irq), then they will not have been enabled
* for us: do so
*/
gic_secondary_init(0);
/*
* let the primary processor know we're out of the
* pen, then head off into the C entry point
*/
write_pen_release(-1);
/*
* Synchronise with the boot thread.
*/
spin_lock(&boot_lock);
spin_unlock(&boot_lock);
}
static int __cpuinit ux500_boot_secondary(unsigned int cpu, struct task_struct *idle)
{
unsigned long timeout;
/*
* set synchronisation state between this boot processor
* and the secondary one
*/
spin_lock(&boot_lock);
/*
* The secondary processor is waiting to be released from
* the holding pen - release it, then wait for it to flag
* that it has been released by resetting pen_release.
*/
write_pen_release(cpu_logical_map(cpu));
arch_send_wakeup_ipi_mask(cpumask_of(cpu));
timeout = jiffies + (1 * HZ);
while (time_before(jiffies, timeout)) {
if (pen_release == -1)
break;
}
/*
* now the secondary core is starting up let it run its
* calibrations, then wait for it to finish
*/
spin_unlock(&boot_lock);
return pen_release != -1 ? -ENOSYS : 0;
}
static void __init wakeup_secondary(void)
{
void __iomem *backupram;
if (cpu_is_u8500_family() || cpu_is_ux540_family())
backupram = __io_address(U8500_BACKUPRAM0_BASE);
else
ux500_unknown_soc();
/*
* write the address of secondary startup into the backup ram register
* at offset 0x1FF4, then write the magic number 0xA1FEED01 to the
* backup ram register at offset 0x1FF0, which is what boot rom code
* is waiting for. This would wake up the secondary core from WFE
*/
#define UX500_CPU1_JUMPADDR_OFFSET 0x1FF4
__raw_writel(virt_to_phys(u8500_secondary_startup),
backupram + UX500_CPU1_JUMPADDR_OFFSET);
#define UX500_CPU1_WAKEMAGIC_OFFSET 0x1FF0
__raw_writel(0xA1FEED01,
backupram + UX500_CPU1_WAKEMAGIC_OFFSET);
/* make sure write buffer is drained */
mb();
}
/*
* Initialise the CPU possible map early - this describes the CPUs
* which may be present or become present in the system.
*/
static void __init ux500_smp_init_cpus(void)
{
void __iomem *scu_base = scu_base_addr();
unsigned int i, ncores;
ncores = scu_base ? scu_get_core_count(scu_base) : 1;
/* sanity check */
if (ncores > nr_cpu_ids) {
pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
ncores, nr_cpu_ids);
ncores = nr_cpu_ids;
}
for (i = 0; i < ncores; i++)
set_cpu_possible(i, true);
}
static void __init ux500_smp_prepare_cpus(unsigned int max_cpus)
{
scu_enable(scu_base_addr());
wakeup_secondary();
}
struct smp_operations ux500_smp_ops __initdata = {
.smp_init_cpus = ux500_smp_init_cpus,
.smp_prepare_cpus = ux500_smp_prepare_cpus,
.smp_secondary_init = ux500_secondary_init,
.smp_boot_secondary = ux500_boot_secondary,
#ifdef CONFIG_HOTPLUG_CPU
.cpu_die = ux500_cpu_die,
#endif
};