swh:1:snp:49cd9498d6cccc5e78252c27dcb645bcf7bf0c91
Tip revision: 88026842b0a760145aa71d69e74fbc9ec118ca44 authored by Linus Torvalds on 03 January 2006, 03:21:10 UTC
Linux v2.6.15
Linux v2.6.15
Tip revision: 8802684
Kconfig
#
# For a description of the syntax of this configuration file,
# see the Configure script.
#
mainmenu "Linux/CRIS Kernel Configuration"
config MMU
bool
default y
config UID16
bool
default y
config RWSEM_GENERIC_SPINLOCK
bool
default y
config RWSEM_XCHGADD_ALGORITHM
bool
config GENERIC_CALIBRATE_DELAY
bool
default y
config CRIS
bool
default y
source "init/Kconfig"
menu "General setup"
source "fs/Kconfig.binfmt"
config ETRAX_CMDLINE
string "Kernel command line"
default "root=/dev/mtdblock3"
help
Pass additional commands to the kernel.
config ETRAX_WATCHDOG
bool "Enable ETRAX watchdog"
help
Enable the built-in watchdog timer support on ETRAX based embedded
network computers.
config ETRAX_WATCHDOG_NICE_DOGGY
bool "Disable watchdog during Oops printouts"
depends on ETRAX_WATCHDOG
help
By enabling this you make sure that the watchdog does not bite while
printing oopses. Recommended for development systems but not for
production releases.
config ETRAX_FAST_TIMER
bool "Enable ETRAX fast timer API"
help
This options enables the API to a fast timer implementation using
timer1 to get sub jiffie resolution timers (primarily one-shot
timers).
This is needed if CONFIG_ETRAX_SERIAL_FAST_TIMER is enabled.
config PREEMPT
bool "Preemptible Kernel"
help
This option reduces the latency of the kernel when reacting to
real-time or interactive events by allowing a low priority process to
be preempted even if it is in kernel mode executing a system call.
This allows applications to run more reliably even when the system is
under load.
Say Y here if you are building a kernel for a desktop, embedded
or real-time system. Say N if you are unsure.
source mm/Kconfig
endmenu
menu "Hardware setup"
choice
prompt "Processor type"
default ETRAX100LX
config ETRAX100LX
bool "ETRAX-100LX-v1"
help
Support version 1 of the ETRAX 100LX.
config ETRAX100LX_V2
bool "ETRAX-100LX-v2"
help
Support version 2 of the ETRAX 100LX.
config SVINTO_SIM
bool "ETRAX-100LX-for-xsim-simulator"
help
Support the xsim ETRAX Simulator.
endchoice
config ETRAX_ARCH_V10
bool
default y if ETRAX100LX || ETRAX100LX_V2
default n if !(ETRAX100LX || ETRAX100LX_V2)
config ETRAX_DRAM_SIZE
int "DRAM size (dec, in MB)"
default "8"
help
Size of DRAM (decimal in MB) typically 2, 8 or 16.
config ETRAX_FLASH_BUSWIDTH
int "Buswidth of flash in bytes"
default "2"
help
Width in bytes of the Flash bus (1, 2 or 4). Is usually 2.
source arch/cris/arch-v10/Kconfig
endmenu
source "net/Kconfig"
# bring in ETRAX built-in drivers
menu "Drivers for built-in interfaces"
source arch/cris/arch-v10/drivers/Kconfig
endmenu
source "drivers/base/Kconfig"
# standard linux drivers
source "drivers/mtd/Kconfig"
source "drivers/parport/Kconfig"
source "drivers/pnp/Kconfig"
source "drivers/block/Kconfig"
source "drivers/md/Kconfig"
source "drivers/ide/Kconfig"
source "drivers/scsi/Kconfig"
source "drivers/ieee1394/Kconfig"
source "drivers/message/i2o/Kconfig"
source "drivers/net/Kconfig"
source "drivers/isdn/Kconfig"
source "drivers/telephony/Kconfig"
source "drivers/cdrom/Kconfig"
#
# input before char - char/joystick depends on it. As does USB.
#
source "drivers/input/Kconfig"
source "drivers/char/Kconfig"
#source drivers/misc/Config.in
source "drivers/media/Kconfig"
source "fs/Kconfig"
source "sound/Kconfig"
source "drivers/usb/Kconfig"
source "arch/cris/Kconfig.debug"
source "security/Kconfig"
source "crypto/Kconfig"
source "lib/Kconfig"