swh:1:snp:49cd9498d6cccc5e78252c27dcb645bcf7bf0c91
Tip revision: 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe authored by Linus Torvalds on 22 July 2011, 02:17:23 UTC
Linux 3.0
Linux 3.0
Tip revision: 02f8c6a
sdio.c
/*
* linux/drivers/mmc/sdio.c
*
* Copyright 2006-2007 Pierre Ossman
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or (at
* your option) any later version.
*/
#include <linux/err.h>
#include <linux/pm_runtime.h>
#include <linux/mmc/host.h>
#include <linux/mmc/card.h>
#include <linux/mmc/sdio.h>
#include <linux/mmc/sdio_func.h>
#include <linux/mmc/sdio_ids.h>
#include "core.h"
#include "bus.h"
#include "sd.h"
#include "sdio_bus.h"
#include "mmc_ops.h"
#include "sd_ops.h"
#include "sdio_ops.h"
#include "sdio_cis.h"
static int sdio_read_fbr(struct sdio_func *func)
{
int ret;
unsigned char data;
if (mmc_card_nonstd_func_interface(func->card)) {
func->class = SDIO_CLASS_NONE;
return 0;
}
ret = mmc_io_rw_direct(func->card, 0, 0,
SDIO_FBR_BASE(func->num) + SDIO_FBR_STD_IF, 0, &data);
if (ret)
goto out;
data &= 0x0f;
if (data == 0x0f) {
ret = mmc_io_rw_direct(func->card, 0, 0,
SDIO_FBR_BASE(func->num) + SDIO_FBR_STD_IF_EXT, 0, &data);
if (ret)
goto out;
}
func->class = data;
out:
return ret;
}
static int sdio_init_func(struct mmc_card *card, unsigned int fn)
{
int ret;
struct sdio_func *func;
BUG_ON(fn > SDIO_MAX_FUNCS);
func = sdio_alloc_func(card);
if (IS_ERR(func))
return PTR_ERR(func);
func->num = fn;
if (!(card->quirks & MMC_QUIRK_NONSTD_SDIO)) {
ret = sdio_read_fbr(func);
if (ret)
goto fail;
ret = sdio_read_func_cis(func);
if (ret)
goto fail;
} else {
func->vendor = func->card->cis.vendor;
func->device = func->card->cis.device;
func->max_blksize = func->card->cis.blksize;
}
card->sdio_func[fn - 1] = func;
return 0;
fail:
/*
* It is okay to remove the function here even though we hold
* the host lock as we haven't registered the device yet.
*/
sdio_remove_func(func);
return ret;
}
static int sdio_read_cccr(struct mmc_card *card)
{
int ret;
int cccr_vsn;
unsigned char data;
memset(&card->cccr, 0, sizeof(struct sdio_cccr));
ret = mmc_io_rw_direct(card, 0, 0, SDIO_CCCR_CCCR, 0, &data);
if (ret)
goto out;
cccr_vsn = data & 0x0f;
if (cccr_vsn > SDIO_CCCR_REV_1_20) {
printk(KERN_ERR "%s: unrecognised CCCR structure version %d\n",
mmc_hostname(card->host), cccr_vsn);
return -EINVAL;
}
card->cccr.sdio_vsn = (data & 0xf0) >> 4;
ret = mmc_io_rw_direct(card, 0, 0, SDIO_CCCR_CAPS, 0, &data);
if (ret)
goto out;
if (data & SDIO_CCCR_CAP_SMB)
card->cccr.multi_block = 1;
if (data & SDIO_CCCR_CAP_LSC)
card->cccr.low_speed = 1;
if (data & SDIO_CCCR_CAP_4BLS)
card->cccr.wide_bus = 1;
if (cccr_vsn >= SDIO_CCCR_REV_1_10) {
ret = mmc_io_rw_direct(card, 0, 0, SDIO_CCCR_POWER, 0, &data);
if (ret)
goto out;
if (data & SDIO_POWER_SMPC)
card->cccr.high_power = 1;
}
if (cccr_vsn >= SDIO_CCCR_REV_1_20) {
ret = mmc_io_rw_direct(card, 0, 0, SDIO_CCCR_SPEED, 0, &data);
if (ret)
goto out;
if (data & SDIO_SPEED_SHS)
card->cccr.high_speed = 1;
}
out:
return ret;
}
static int sdio_enable_wide(struct mmc_card *card)
{
int ret;
u8 ctrl;
if (!(card->host->caps & MMC_CAP_4_BIT_DATA))
return 0;
if (card->cccr.low_speed && !card->cccr.wide_bus)
return 0;
ret = mmc_io_rw_direct(card, 0, 0, SDIO_CCCR_IF, 0, &ctrl);
if (ret)
return ret;
ctrl |= SDIO_BUS_WIDTH_4BIT;
ret = mmc_io_rw_direct(card, 1, 0, SDIO_CCCR_IF, ctrl, NULL);
if (ret)
return ret;
return 1;
}
/*
* If desired, disconnect the pull-up resistor on CD/DAT[3] (pin 1)
* of the card. This may be required on certain setups of boards,
* controllers and embedded sdio device which do not need the card's
* pull-up. As a result, card detection is disabled and power is saved.
*/
static int sdio_disable_cd(struct mmc_card *card)
{
int ret;
u8 ctrl;
if (!mmc_card_disable_cd(card))
return 0;
ret = mmc_io_rw_direct(card, 0, 0, SDIO_CCCR_IF, 0, &ctrl);
if (ret)
return ret;
ctrl |= SDIO_BUS_CD_DISABLE;
return mmc_io_rw_direct(card, 1, 0, SDIO_CCCR_IF, ctrl, NULL);
}
/*
* Devices that remain active during a system suspend are
* put back into 1-bit mode.
*/
static int sdio_disable_wide(struct mmc_card *card)
{
int ret;
u8 ctrl;
if (!(card->host->caps & MMC_CAP_4_BIT_DATA))
return 0;
if (card->cccr.low_speed && !card->cccr.wide_bus)
return 0;
ret = mmc_io_rw_direct(card, 0, 0, SDIO_CCCR_IF, 0, &ctrl);
if (ret)
return ret;
if (!(ctrl & SDIO_BUS_WIDTH_4BIT))
return 0;
ctrl &= ~SDIO_BUS_WIDTH_4BIT;
ctrl |= SDIO_BUS_ASYNC_INT;
ret = mmc_io_rw_direct(card, 1, 0, SDIO_CCCR_IF, ctrl, NULL);
if (ret)
return ret;
mmc_set_bus_width(card->host, MMC_BUS_WIDTH_1);
return 0;
}
static int sdio_enable_4bit_bus(struct mmc_card *card)
{
int err;
if (card->type == MMC_TYPE_SDIO)
return sdio_enable_wide(card);
if ((card->host->caps & MMC_CAP_4_BIT_DATA) &&
(card->scr.bus_widths & SD_SCR_BUS_WIDTH_4)) {
err = mmc_app_set_bus_width(card, MMC_BUS_WIDTH_4);
if (err)
return err;
} else
return 0;
err = sdio_enable_wide(card);
if (err <= 0)
mmc_app_set_bus_width(card, MMC_BUS_WIDTH_1);
return err;
}
/*
* Test if the card supports high-speed mode and, if so, switch to it.
*/
static int mmc_sdio_switch_hs(struct mmc_card *card, int enable)
{
int ret;
u8 speed;
if (!(card->host->caps & MMC_CAP_SD_HIGHSPEED))
return 0;
if (!card->cccr.high_speed)
return 0;
ret = mmc_io_rw_direct(card, 0, 0, SDIO_CCCR_SPEED, 0, &speed);
if (ret)
return ret;
if (enable)
speed |= SDIO_SPEED_EHS;
else
speed &= ~SDIO_SPEED_EHS;
ret = mmc_io_rw_direct(card, 1, 0, SDIO_CCCR_SPEED, speed, NULL);
if (ret)
return ret;
return 1;
}
/*
* Enable SDIO/combo card's high-speed mode. Return 0/1 if [not]supported.
*/
static int sdio_enable_hs(struct mmc_card *card)
{
int ret;
ret = mmc_sdio_switch_hs(card, true);
if (ret <= 0 || card->type == MMC_TYPE_SDIO)
return ret;
ret = mmc_sd_switch_hs(card);
if (ret <= 0)
mmc_sdio_switch_hs(card, false);
return ret;
}
static unsigned mmc_sdio_get_max_clock(struct mmc_card *card)
{
unsigned max_dtr;
if (mmc_card_highspeed(card)) {
/*
* The SDIO specification doesn't mention how
* the CIS transfer speed register relates to
* high-speed, but it seems that 50 MHz is
* mandatory.
*/
max_dtr = 50000000;
} else {
max_dtr = card->cis.max_dtr;
}
if (card->type == MMC_TYPE_SD_COMBO)
max_dtr = min(max_dtr, mmc_sd_get_max_clock(card));
return max_dtr;
}
/*
* Handle the detection and initialisation of a card.
*
* In the case of a resume, "oldcard" will contain the card
* we're trying to reinitialise.
*/
static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr,
struct mmc_card *oldcard, int powered_resume)
{
struct mmc_card *card;
int err;
BUG_ON(!host);
WARN_ON(!host->claimed);
/*
* Inform the card of the voltage
*/
if (!powered_resume) {
err = mmc_send_io_op_cond(host, host->ocr, &ocr);
if (err)
goto err;
}
/*
* For SPI, enable CRC as appropriate.
*/
if (mmc_host_is_spi(host)) {
err = mmc_spi_set_crc(host, use_spi_crc);
if (err)
goto err;
}
/*
* Allocate card structure.
*/
card = mmc_alloc_card(host, NULL);
if (IS_ERR(card)) {
err = PTR_ERR(card);
goto err;
}
if ((ocr & R4_MEMORY_PRESENT) &&
mmc_sd_get_cid(host, host->ocr & ocr, card->raw_cid, NULL) == 0) {
card->type = MMC_TYPE_SD_COMBO;
if (oldcard && (oldcard->type != MMC_TYPE_SD_COMBO ||
memcmp(card->raw_cid, oldcard->raw_cid, sizeof(card->raw_cid)) != 0)) {
mmc_remove_card(card);
return -ENOENT;
}
} else {
card->type = MMC_TYPE_SDIO;
if (oldcard && oldcard->type != MMC_TYPE_SDIO) {
mmc_remove_card(card);
return -ENOENT;
}
}
/*
* Call the optional HC's init_card function to handle quirks.
*/
if (host->ops->init_card)
host->ops->init_card(host, card);
/*
* For native busses: set card RCA and quit open drain mode.
*/
if (!powered_resume && !mmc_host_is_spi(host)) {
err = mmc_send_relative_addr(host, &card->rca);
if (err)
goto remove;
/*
* Update oldcard with the new RCA received from the SDIO
* device -- we're doing this so that it's updated in the
* "card" struct when oldcard overwrites that later.
*/
if (oldcard)
oldcard->rca = card->rca;
mmc_set_bus_mode(host, MMC_BUSMODE_PUSHPULL);
}
/*
* Read CSD, before selecting the card
*/
if (!oldcard && card->type == MMC_TYPE_SD_COMBO) {
err = mmc_sd_get_csd(host, card);
if (err)
return err;
mmc_decode_cid(card);
}
/*
* Select card, as all following commands rely on that.
*/
if (!powered_resume && !mmc_host_is_spi(host)) {
err = mmc_select_card(card);
if (err)
goto remove;
}
if (card->quirks & MMC_QUIRK_NONSTD_SDIO) {
/*
* This is non-standard SDIO device, meaning it doesn't
* have any CIA (Common I/O area) registers present.
* It's host's responsibility to fill cccr and cis
* structures in init_card().
*/
mmc_set_clock(host, card->cis.max_dtr);
if (card->cccr.high_speed) {
mmc_card_set_highspeed(card);
mmc_set_timing(card->host, MMC_TIMING_SD_HS);
}
goto finish;
}
/*
* Read the common registers.
*/
err = sdio_read_cccr(card);
if (err)
goto remove;
/*
* Read the common CIS tuples.
*/
err = sdio_read_common_cis(card);
if (err)
goto remove;
if (oldcard) {
int same = (card->cis.vendor == oldcard->cis.vendor &&
card->cis.device == oldcard->cis.device);
mmc_remove_card(card);
if (!same)
return -ENOENT;
card = oldcard;
}
mmc_fixup_device(card, NULL);
if (card->type == MMC_TYPE_SD_COMBO) {
err = mmc_sd_setup_card(host, card, oldcard != NULL);
/* handle as SDIO-only card if memory init failed */
if (err) {
mmc_go_idle(host);
if (mmc_host_is_spi(host))
/* should not fail, as it worked previously */
mmc_spi_set_crc(host, use_spi_crc);
card->type = MMC_TYPE_SDIO;
} else
card->dev.type = &sd_type;
}
/*
* If needed, disconnect card detection pull-up resistor.
*/
err = sdio_disable_cd(card);
if (err)
goto remove;
/*
* Switch to high-speed (if supported).
*/
err = sdio_enable_hs(card);
if (err > 0)
mmc_sd_go_highspeed(card);
else if (err)
goto remove;
/*
* Change to the card's maximum speed.
*/
mmc_set_clock(host, mmc_sdio_get_max_clock(card));
/*
* Switch to wider bus (if supported).
*/
err = sdio_enable_4bit_bus(card);
if (err > 0)
mmc_set_bus_width(card->host, MMC_BUS_WIDTH_4);
else if (err)
goto remove;
finish:
if (!oldcard)
host->card = card;
return 0;
remove:
if (!oldcard)
mmc_remove_card(card);
err:
return err;
}
/*
* Host is being removed. Free up the current card.
*/
static void mmc_sdio_remove(struct mmc_host *host)
{
int i;
BUG_ON(!host);
BUG_ON(!host->card);
for (i = 0;i < host->card->sdio_funcs;i++) {
if (host->card->sdio_func[i]) {
sdio_remove_func(host->card->sdio_func[i]);
host->card->sdio_func[i] = NULL;
}
}
mmc_remove_card(host->card);
host->card = NULL;
}
/*
* Card detection callback from host.
*/
static void mmc_sdio_detect(struct mmc_host *host)
{
int err;
BUG_ON(!host);
BUG_ON(!host->card);
/* Make sure card is powered before detecting it */
if (host->caps & MMC_CAP_POWER_OFF_CARD) {
err = pm_runtime_get_sync(&host->card->dev);
if (err < 0)
goto out;
}
mmc_claim_host(host);
/*
* Just check if our card has been removed.
*/
err = mmc_select_card(host->card);
mmc_release_host(host);
/*
* Tell PM core it's OK to power off the card now.
*
* The _sync variant is used in order to ensure that the card
* is left powered off in case an error occurred, and the card
* is going to be removed.
*
* Since there is no specific reason to believe a new user
* is about to show up at this point, the _sync variant is
* desirable anyway.
*/
if (host->caps & MMC_CAP_POWER_OFF_CARD)
pm_runtime_put_sync(&host->card->dev);
out:
if (err) {
mmc_sdio_remove(host);
mmc_claim_host(host);
mmc_detach_bus(host);
mmc_release_host(host);
}
}
/*
* SDIO suspend. We need to suspend all functions separately.
* Therefore all registered functions must have drivers with suspend
* and resume methods. Failing that we simply remove the whole card.
*/
static int mmc_sdio_suspend(struct mmc_host *host)
{
int i, err = 0;
for (i = 0; i < host->card->sdio_funcs; i++) {
struct sdio_func *func = host->card->sdio_func[i];
if (func && sdio_func_present(func) && func->dev.driver) {
const struct dev_pm_ops *pmops = func->dev.driver->pm;
if (!pmops || !pmops->suspend || !pmops->resume) {
/* force removal of entire card in that case */
err = -ENOSYS;
} else
err = pmops->suspend(&func->dev);
if (err)
break;
}
}
while (err && --i >= 0) {
struct sdio_func *func = host->card->sdio_func[i];
if (func && sdio_func_present(func) && func->dev.driver) {
const struct dev_pm_ops *pmops = func->dev.driver->pm;
pmops->resume(&func->dev);
}
}
if (!err && mmc_card_keep_power(host) && mmc_card_wake_sdio_irq(host)) {
mmc_claim_host(host);
sdio_disable_wide(host->card);
mmc_release_host(host);
}
return err;
}
static int mmc_sdio_resume(struct mmc_host *host)
{
int i, err = 0;
BUG_ON(!host);
BUG_ON(!host->card);
/* Basic card reinitialization. */
mmc_claim_host(host);
/* No need to reinitialize powered-resumed nonremovable cards */
if (mmc_card_is_removable(host) || !mmc_card_keep_power(host))
err = mmc_sdio_init_card(host, host->ocr, host->card,
mmc_card_keep_power(host));
else if (mmc_card_keep_power(host) && mmc_card_wake_sdio_irq(host)) {
/* We may have switched to 1-bit mode during suspend */
err = sdio_enable_4bit_bus(host->card);
if (err > 0) {
mmc_set_bus_width(host, MMC_BUS_WIDTH_4);
err = 0;
}
}
if (!err && host->sdio_irqs)
mmc_signal_sdio_irq(host);
mmc_release_host(host);
/*
* If the card looked to be the same as before suspending, then
* we proceed to resume all card functions. If one of them returns
* an error then we simply return that error to the core and the
* card will be redetected as new. It is the responsibility of
* the function driver to perform further tests with the extra
* knowledge it has of the card to confirm the card is indeed the
* same as before suspending (same MAC address for network cards,
* etc.) and return an error otherwise.
*/
for (i = 0; !err && i < host->card->sdio_funcs; i++) {
struct sdio_func *func = host->card->sdio_func[i];
if (func && sdio_func_present(func) && func->dev.driver) {
const struct dev_pm_ops *pmops = func->dev.driver->pm;
err = pmops->resume(&func->dev);
}
}
return err;
}
static int mmc_sdio_power_restore(struct mmc_host *host)
{
int ret;
u32 ocr;
BUG_ON(!host);
BUG_ON(!host->card);
mmc_claim_host(host);
/*
* Reset the card by performing the same steps that are taken by
* mmc_rescan_try_freq() and mmc_attach_sdio() during a "normal" probe.
*
* sdio_reset() is technically not needed. Having just powered up the
* hardware, it should already be in reset state. However, some
* platforms (such as SD8686 on OLPC) do not instantly cut power,
* meaning that a reset is required when restoring power soon after
* powering off. It is harmless in other cases.
*
* The CMD5 reset (mmc_send_io_op_cond()), according to the SDIO spec,
* is not necessary for non-removable cards. However, it is required
* for OLPC SD8686 (which expects a [CMD5,5,3,7] init sequence), and
* harmless in other situations.
*
* With these steps taken, mmc_select_voltage() is also required to
* restore the correct voltage setting of the card.
*/
sdio_reset(host);
mmc_go_idle(host);
mmc_send_if_cond(host, host->ocr_avail);
ret = mmc_send_io_op_cond(host, 0, &ocr);
if (ret)
goto out;
if (host->ocr_avail_sdio)
host->ocr_avail = host->ocr_avail_sdio;
host->ocr = mmc_select_voltage(host, ocr & ~0x7F);
if (!host->ocr) {
ret = -EINVAL;
goto out;
}
ret = mmc_sdio_init_card(host, host->ocr, host->card,
mmc_card_keep_power(host));
if (!ret && host->sdio_irqs)
mmc_signal_sdio_irq(host);
out:
mmc_release_host(host);
return ret;
}
static const struct mmc_bus_ops mmc_sdio_ops = {
.remove = mmc_sdio_remove,
.detect = mmc_sdio_detect,
.suspend = mmc_sdio_suspend,
.resume = mmc_sdio_resume,
.power_restore = mmc_sdio_power_restore,
};
/*
* Starting point for SDIO card init.
*/
int mmc_attach_sdio(struct mmc_host *host)
{
int err, i, funcs;
u32 ocr;
struct mmc_card *card;
BUG_ON(!host);
WARN_ON(!host->claimed);
err = mmc_send_io_op_cond(host, 0, &ocr);
if (err)
return err;
mmc_attach_bus(host, &mmc_sdio_ops);
if (host->ocr_avail_sdio)
host->ocr_avail = host->ocr_avail_sdio;
/*
* Sanity check the voltages that the card claims to
* support.
*/
if (ocr & 0x7F) {
printk(KERN_WARNING "%s: card claims to support voltages "
"below the defined range. These will be ignored.\n",
mmc_hostname(host));
ocr &= ~0x7F;
}
host->ocr = mmc_select_voltage(host, ocr);
/*
* Can we support the voltage(s) of the card(s)?
*/
if (!host->ocr) {
err = -EINVAL;
goto err;
}
/*
* Detect and init the card.
*/
err = mmc_sdio_init_card(host, host->ocr, NULL, 0);
if (err)
goto err;
card = host->card;
/*
* Enable runtime PM only if supported by host+card+board
*/
if (host->caps & MMC_CAP_POWER_OFF_CARD) {
/*
* Let runtime PM core know our card is active
*/
err = pm_runtime_set_active(&card->dev);
if (err)
goto remove;
/*
* Enable runtime PM for this card
*/
pm_runtime_enable(&card->dev);
}
/*
* The number of functions on the card is encoded inside
* the ocr.
*/
funcs = (ocr & 0x70000000) >> 28;
card->sdio_funcs = 0;
/*
* Initialize (but don't add) all present functions.
*/
for (i = 0; i < funcs; i++, card->sdio_funcs++) {
err = sdio_init_func(host->card, i + 1);
if (err)
goto remove;
/*
* Enable Runtime PM for this func (if supported)
*/
if (host->caps & MMC_CAP_POWER_OFF_CARD)
pm_runtime_enable(&card->sdio_func[i]->dev);
}
/*
* First add the card to the driver model...
*/
mmc_release_host(host);
err = mmc_add_card(host->card);
if (err)
goto remove_added;
/*
* ...then the SDIO functions.
*/
for (i = 0;i < funcs;i++) {
err = sdio_add_func(host->card->sdio_func[i]);
if (err)
goto remove_added;
}
mmc_claim_host(host);
return 0;
remove_added:
/* Remove without lock if the device has been added. */
mmc_sdio_remove(host);
mmc_claim_host(host);
remove:
/* And with lock if it hasn't been added. */
mmc_release_host(host);
if (host->card)
mmc_sdio_remove(host);
mmc_claim_host(host);
err:
mmc_detach_bus(host);
printk(KERN_ERR "%s: error %d whilst initialising SDIO card\n",
mmc_hostname(host), err);
return err;
}