swh:1:snp:49cd9498d6cccc5e78252c27dcb645bcf7bf0c91
Tip revision: bcf876870b95592b52519ed4aafcf9d95999bc9c authored by Linus Torvalds on 02 August 2020, 21:21:45 UTC
Linux 5.8
Linux 5.8
Tip revision: bcf8768
Kconfig
# SPDX-License-Identifier: GPL-2.0
#
# PCI Express Port Bus Configuration
#
config PCIEPORTBUS
bool "PCI Express Port Bus support"
help
This enables PCI Express Port Bus support. Users can then enable
support for Native Hot-Plug, Advanced Error Reporting, Power
Management Events, and Downstream Port Containment.
#
# Include service Kconfig here
#
config HOTPLUG_PCI_PCIE
bool "PCI Express Hotplug driver"
depends on HOTPLUG_PCI && PCIEPORTBUS
help
Say Y here if you have a motherboard that supports PCI Express Native
Hotplug
When in doubt, say N.
config PCIEAER
bool "PCI Express Advanced Error Reporting support"
depends on PCIEPORTBUS
select RAS
help
This enables PCI Express Root Port Advanced Error Reporting
(AER) driver support. Error reporting messages sent to Root
Port will be handled by PCI Express AER driver.
config PCIEAER_INJECT
tristate "PCI Express error injection support"
depends on PCIEAER
select GENERIC_IRQ_INJECTION
help
This enables PCI Express Root Port Advanced Error Reporting
(AER) software error injector.
Debugging AER code is quite difficult because it is hard
to trigger various real hardware errors. Software-based
error injection can fake almost all kinds of errors with the
help of a user space helper tool aer-inject, which can be
gotten from:
http://www.kernel.org/pub/linux/utils/pci/aer-inject/
#
# PCI Express ECRC
#
config PCIE_ECRC
bool "PCI Express ECRC settings control"
depends on PCIEAER
help
Used to override firmware/bios settings for PCI Express ECRC
(transaction layer end-to-end CRC checking).
When in doubt, say N.
#
# PCI Express ASPM
#
config PCIEASPM
bool "PCI Express ASPM control" if EXPERT
default y
help
This enables OS control over PCI Express ASPM (Active State
Power Management) and Clock Power Management. ASPM supports
state L0/L0s/L1.
ASPM is initially set up by the firmware. With this option enabled,
Linux can modify this state in order to disable ASPM on known-bad
hardware or configurations and enable it when known-safe.
ASPM can be disabled or enabled at runtime via
/sys/module/pcie_aspm/parameters/policy
When in doubt, say Y.
choice
prompt "Default ASPM policy"
default PCIEASPM_DEFAULT
depends on PCIEASPM
config PCIEASPM_DEFAULT
bool "BIOS default"
depends on PCIEASPM
help
Use the BIOS defaults for PCI Express ASPM.
config PCIEASPM_POWERSAVE
bool "Powersave"
depends on PCIEASPM
help
Enable PCI Express ASPM L0s and L1 where possible, even if the
BIOS did not.
config PCIEASPM_POWER_SUPERSAVE
bool "Power Supersave"
depends on PCIEASPM
help
Same as PCIEASPM_POWERSAVE, except it also enables L1 substates where
possible. This would result in higher power savings while staying in L1
where the components support it.
config PCIEASPM_PERFORMANCE
bool "Performance"
depends on PCIEASPM
help
Disable PCI Express ASPM L0s and L1, even if the BIOS enabled them.
endchoice
config PCIE_PME
def_bool y
depends on PCIEPORTBUS && PM
config PCIE_DPC
bool "PCI Express Downstream Port Containment support"
depends on PCIEPORTBUS && PCIEAER
help
This enables PCI Express Downstream Port Containment (DPC)
driver support. DPC events from Root and Downstream ports
will be handled by the DPC driver. If your system doesn't
have this capability or you do not want to use this feature,
it is safe to answer N.
config PCIE_PTM
bool "PCI Express Precision Time Measurement support"
help
This enables PCI Express Precision Time Measurement (PTM)
support.
This is only useful if you have devices that support PTM, but it
is safe to enable even if you don't.
config PCIE_BW
bool "PCI Express Bandwidth Change Notification"
depends on PCIEPORTBUS
help
This enables PCI Express Bandwidth Change Notification. If
you know link width or rate changes occur only to correct
unreliable links, you may answer Y.
config PCIE_EDR
bool "PCI Express Error Disconnect Recover support"
depends on PCIE_DPC && ACPI
help
This option adds Error Disconnect Recover support as specified
in the Downstream Port Containment Related Enhancements ECN to
the PCI Firmware Specification r3.2. Enable this if you want to
support hybrid DPC model which uses both firmware and OS to
implement DPC.