swh:1:snp:49cd9498d6cccc5e78252c27dcb645bcf7bf0c91
Tip revision: 7d2a07b769330c34b4deabeed939325c77a7ec2f authored by Linus Torvalds on 29 August 2021, 22:04:50 UTC
Linux 5.14
Linux 5.14
Tip revision: 7d2a07b
Kconfig
# SPDX-License-Identifier: GPL-2.0
menuconfig TYPEC
tristate "USB Type-C Support"
help
USB Type-C Specification defines a cable and connector for USB where
only one type of plug is supported on both ends, i.e. there will not
be Type-A plug on one end of the cable and Type-B plug on the other.
Determination of the host-to-device relationship happens through a
specific Configuration Channel (CC) which goes through the USB Type-C
cable. The Configuration Channel may also be used to detect optional
Accessory Modes - Analog Audio and Debug - and if USB Power Delivery
is supported, the Alternate Modes, where the connector is used for
something else then USB communication.
USB Power Delivery Specification defines a protocol that can be used
to negotiate the voltage and current levels with the connected
partners. USB Power Delivery allows higher voltages then the normal
5V, up to 20V, and current up to 5A over the cable. The USB Power
Delivery protocol is also used to negotiate the optional Alternate
Modes when they are supported. USB Power Delivery does not depend on
USB Type-C connector, however it is mostly used together with USB
Type-C connectors.
USB Type-C and USB Power Delivery Specifications define a set of state
machines that need to be implemented in either software or firmware.
Simple USB Type-C PHYs, for example USB Type-C Port Controller
Interface Specification compliant "Port Controllers" need the state
machines to be handled in the OS, but stand-alone USB Type-C and Power
Delivery controllers handle the state machines inside their firmware.
The USB Type-C and Power Delivery controllers usually function
autonomously, and do not necessarily require drivers.
Enable this configurations option if you have USB Type-C connectors on
your system and 1) you know your USB Type-C hardware requires OS
control (a driver) to function, or 2) if you need to be able to read
the status of the USB Type-C ports in your system, or 3) if you need
to be able to swap the power role (decide are you supplying or
consuming power over the cable) or data role (host or device) when
both roles are supported.
For more information, see the kernel documentation for USB Type-C
Connector Class API (Documentation/driver-api/usb/typec.rst)
<https://www.kernel.org/doc/html/latest/driver-api/usb/typec.html>
and ABI (Documentation/ABI/testing/sysfs-class-typec).
if TYPEC
source "drivers/usb/typec/tcpm/Kconfig"
source "drivers/usb/typec/ucsi/Kconfig"
source "drivers/usb/typec/tipd/Kconfig"
config TYPEC_HD3SS3220
tristate "TI HD3SS3220 Type-C DRP Port controller driver"
depends on I2C
depends on USB_ROLE_SWITCH
help
Say Y or M here if your system has TI HD3SS3220 Type-C DRP Port
controller driver.
If you choose to build this driver as a dynamically linked module, the
module will be called hd3ss3220.ko.
config TYPEC_STUSB160X
tristate "STMicroelectronics STUSB160x Type-C controller driver"
depends on I2C
depends on REGMAP_I2C
depends on USB_ROLE_SWITCH || !USB_ROLE_SWITCH
help
Say Y or M here if your system has STMicroelectronics STUSB160x
Type-C port controller.
If you choose to build this driver as a dynamically linked module, the
module will be called stusb160x.ko.
config TYPEC_QCOM_PMIC
tristate "Qualcomm PMIC USB Type-C driver"
depends on ARCH_QCOM || COMPILE_TEST
depends on USB_ROLE_SWITCH || !USB_ROLE_SWITCH
help
Driver for supporting role switch over the Qualcomm PMIC. This will
handle the USB Type-C role and orientation detection reported by the
QCOM PMIC if the PMIC has the capability to handle USB Type-C
detection.
It will also enable the VBUS output to connected devices when a
DFP connection is made.
source "drivers/usb/typec/mux/Kconfig"
source "drivers/usb/typec/altmodes/Kconfig"
endif # TYPEC