swh:1:snp:77163734605b0ec556b01d897b7bb4a7e30d46b6
Tip revision: 03c765b0e3b4cb5063276b086c76f7a612856a9a authored by Linus Torvalds on 26 June 2022, 21:22:10 UTC
Linux 5.19-rc4
Linux 5.19-rc4
Tip revision: 03c765b
pxa2xx.rst
==============================
PXA2xx SPI on SSP driver HOWTO
==============================
This a mini HOWTO on the pxa2xx_spi driver. The driver turns a PXA2xx
synchronous serial port into an SPI master controller
(see Documentation/spi/spi-summary.rst). The driver has the following features
- Support for any PXA2xx and compatible SSP.
- SSP PIO and SSP DMA data transfers.
- External and Internal (SSPFRM) chip selects.
- Per slave device (chip) configuration.
- Full suspend, freeze, resume support.
The driver is built around a &struct spi_message FIFO serviced by kernel
thread. The kernel thread, spi_pump_messages(), drives message FIFO and
is responsible for queuing SPI transactions and setting up and launching
the DMA or interrupt driven transfers.
Declaring PXA2xx Master Controllers
-----------------------------------
Typically, for a legacy platform, an SPI master is defined in the
arch/.../mach-*/board-*.c as a "platform device". The master configuration
is passed to the driver via a table found in include/linux/spi/pxa2xx_spi.h::
struct pxa2xx_spi_controller {
u16 num_chipselect;
u8 enable_dma;
...
};
The "pxa2xx_spi_controller.num_chipselect" field is used to determine the number of
slave device (chips) attached to this SPI master.
The "pxa2xx_spi_controller.enable_dma" field informs the driver that SSP DMA should
be used. This caused the driver to acquire two DMA channels: Rx channel and
Tx channel. The Rx channel has a higher DMA service priority than the Tx channel.
See the "PXA2xx Developer Manual" section "DMA Controller".
For the new platforms the description of the controller and peripheral devices
comes from Device Tree or ACPI.
NSSP MASTER SAMPLE
------------------
Below is a sample configuration using the PXA255 NSSP for a legacy platform::
static struct resource pxa_spi_nssp_resources[] = {
[0] = {
.start = __PREG(SSCR0_P(2)), /* Start address of NSSP */
.end = __PREG(SSCR0_P(2)) + 0x2c, /* Range of registers */
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_NSSP, /* NSSP IRQ */
.end = IRQ_NSSP,
.flags = IORESOURCE_IRQ,
},
};
static struct pxa2xx_spi_controller pxa_nssp_master_info = {
.num_chipselect = 1, /* Matches the number of chips attached to NSSP */
.enable_dma = 1, /* Enables NSSP DMA */
};
static struct platform_device pxa_spi_nssp = {
.name = "pxa2xx-spi", /* MUST BE THIS VALUE, so device match driver */
.id = 2, /* Bus number, MUST MATCH SSP number 1..n */
.resource = pxa_spi_nssp_resources,
.num_resources = ARRAY_SIZE(pxa_spi_nssp_resources),
.dev = {
.platform_data = &pxa_nssp_master_info, /* Passed to driver */
},
};
static struct platform_device *devices[] __initdata = {
&pxa_spi_nssp,
};
static void __init board_init(void)
{
(void)platform_add_device(devices, ARRAY_SIZE(devices));
}
Declaring Slave Devices
-----------------------
Typically, for a legacy platform, each SPI slave (chip) is defined in the
arch/.../mach-*/board-*.c using the "spi_board_info" structure found in
"linux/spi/spi.h". See "Documentation/spi/spi-summary.rst" for additional
information.
Each slave device attached to the PXA must provide slave specific configuration
information via the structure "pxa2xx_spi_chip" found in
"include/linux/spi/pxa2xx_spi.h". The pxa2xx_spi master controller driver
will uses the configuration whenever the driver communicates with the slave
device. All fields are optional.
::
struct pxa2xx_spi_chip {
u8 tx_threshold;
u8 rx_threshold;
u8 dma_burst_size;
u32 timeout;
};
The "pxa2xx_spi_chip.tx_threshold" and "pxa2xx_spi_chip.rx_threshold" fields are
used to configure the SSP hardware FIFO. These fields are critical to the
performance of pxa2xx_spi driver and misconfiguration will result in rx
FIFO overruns (especially in PIO mode transfers). Good default values are::
.tx_threshold = 8,
.rx_threshold = 8,
The range is 1 to 16 where zero indicates "use default".
The "pxa2xx_spi_chip.dma_burst_size" field is used to configure PXA2xx DMA
engine and is related the "spi_device.bits_per_word" field. Read and understand
the PXA2xx "Developer Manual" sections on the DMA controller and SSP Controllers
to determine the correct value. An SSP configured for byte-wide transfers would
use a value of 8. The driver will determine a reasonable default if
dma_burst_size == 0.
The "pxa2xx_spi_chip.timeout" fields is used to efficiently handle
trailing bytes in the SSP receiver FIFO. The correct value for this field is
dependent on the SPI bus speed ("spi_board_info.max_speed_hz") and the specific
slave device. Please note that the PXA2xx SSP 1 does not support trailing byte
timeouts and must busy-wait any trailing bytes.
NOTE: the SPI driver cannot control the chip select if SSPFRM is used, so the
chipselect is dropped after each spi_transfer. Most devices need chip select
asserted around the complete message. Use SSPFRM as a GPIO (through a descriptor)
to accommodate these chips.
NSSP SLAVE SAMPLE
-----------------
For a legacy platform or in some other cases, the pxa2xx_spi_chip structure
is passed to the pxa2xx_spi driver in the "spi_board_info.controller_data"
field. Below is a sample configuration using the PXA255 NSSP.
::
static struct pxa2xx_spi_chip cs8415a_chip_info = {
.tx_threshold = 8, /* SSP hardward FIFO threshold */
.rx_threshold = 8, /* SSP hardward FIFO threshold */
.dma_burst_size = 8, /* Byte wide transfers used so 8 byte bursts */
.timeout = 235, /* See Intel documentation */
};
static struct pxa2xx_spi_chip cs8405a_chip_info = {
.tx_threshold = 8, /* SSP hardward FIFO threshold */
.rx_threshold = 8, /* SSP hardward FIFO threshold */
.dma_burst_size = 8, /* Byte wide transfers used so 8 byte bursts */
.timeout = 235, /* See Intel documentation */
};
static struct spi_board_info streetracer_spi_board_info[] __initdata = {
{
.modalias = "cs8415a", /* Name of spi_driver for this device */
.max_speed_hz = 3686400, /* Run SSP as fast a possbile */
.bus_num = 2, /* Framework bus number */
.chip_select = 0, /* Framework chip select */
.platform_data = NULL; /* No spi_driver specific config */
.controller_data = &cs8415a_chip_info, /* Master chip config */
.irq = STREETRACER_APCI_IRQ, /* Slave device interrupt */
},
{
.modalias = "cs8405a", /* Name of spi_driver for this device */
.max_speed_hz = 3686400, /* Run SSP as fast a possbile */
.bus_num = 2, /* Framework bus number */
.chip_select = 1, /* Framework chip select */
.controller_data = &cs8405a_chip_info, /* Master chip config */
.irq = STREETRACER_APCI_IRQ, /* Slave device interrupt */
},
};
static void __init streetracer_init(void)
{
spi_register_board_info(streetracer_spi_board_info,
ARRAY_SIZE(streetracer_spi_board_info));
}
DMA and PIO I/O Support
-----------------------
The pxa2xx_spi driver supports both DMA and interrupt driven PIO message
transfers. The driver defaults to PIO mode and DMA transfers must be enabled
by setting the "enable_dma" flag in the "pxa2xx_spi_controller" structure.
For the newer platforms, that are known to support DMA, the driver will enable
it automatically and try it first with a possible fallback to PIO. The DMA
mode supports both coherent and stream based DMA mappings.
The following logic is used to determine the type of I/O to be used on
a per "spi_transfer" basis::
if !enable_dma then
always use PIO transfers
if spi_message.len > 8191 then
print "rate limited" warning
use PIO transfers
if spi_message.is_dma_mapped and rx_dma_buf != 0 and tx_dma_buf != 0 then
use coherent DMA mode
if rx_buf and tx_buf are aligned on 8 byte boundary then
use streaming DMA mode
otherwise
use PIO transfer
THANKS TO
---------
David Brownell and others for mentoring the development of this driver.