swh:1:snp:77163734605b0ec556b01d897b7bb4a7e30d46b6
Tip revision: a351e9b9fc24e982ec2f0e76379a49826036da12 authored by Linus Torvalds on 01 May 2017, 02:47:48 UTC
Linux 4.11
Linux 4.11
Tip revision: a351e9b
m5272.c
/***************************************************************************/
/*
* m5272.c -- platform support for ColdFire 5272 based boards
*
* Copyright (C) 1999-2002, Greg Ungerer (gerg@snapgear.com)
* Copyright (C) 2001-2002, SnapGear Inc. (www.snapgear.com)
*/
/***************************************************************************/
#include <linux/kernel.h>
#include <linux/param.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/phy.h>
#include <linux/phy_fixed.h>
#include <asm/machdep.h>
#include <asm/coldfire.h>
#include <asm/mcfsim.h>
#include <asm/mcfuart.h>
#include <asm/mcfclk.h>
/***************************************************************************/
/*
* Some platforms need software versions of the GPIO data registers.
*/
unsigned short ppdata;
unsigned char ledbank = 0xff;
/***************************************************************************/
DEFINE_CLK(pll, "pll.0", MCF_CLK);
DEFINE_CLK(sys, "sys.0", MCF_BUSCLK);
DEFINE_CLK(mcftmr0, "mcftmr.0", MCF_BUSCLK);
DEFINE_CLK(mcftmr1, "mcftmr.1", MCF_BUSCLK);
DEFINE_CLK(mcftmr2, "mcftmr.2", MCF_BUSCLK);
DEFINE_CLK(mcftmr3, "mcftmr.3", MCF_BUSCLK);
DEFINE_CLK(mcfuart0, "mcfuart.0", MCF_BUSCLK);
DEFINE_CLK(mcfuart1, "mcfuart.1", MCF_BUSCLK);
DEFINE_CLK(mcfqspi0, "mcfqspi.0", MCF_BUSCLK);
DEFINE_CLK(fec0, "fec.0", MCF_BUSCLK);
struct clk *mcf_clks[] = {
&clk_pll,
&clk_sys,
&clk_mcftmr0,
&clk_mcftmr1,
&clk_mcftmr2,
&clk_mcftmr3,
&clk_mcfuart0,
&clk_mcfuart1,
&clk_mcfqspi0,
&clk_fec0,
NULL
};
/***************************************************************************/
static void __init m5272_uarts_init(void)
{
u32 v;
/* Enable the output lines for the serial ports */
v = readl(MCFSIM_PBCNT);
v = (v & ~0x000000ff) | 0x00000055;
writel(v, MCFSIM_PBCNT);
v = readl(MCFSIM_PDCNT);
v = (v & ~0x000003fc) | 0x000002a8;
writel(v, MCFSIM_PDCNT);
}
/***************************************************************************/
static void m5272_cpu_reset(void)
{
local_irq_disable();
/* Set watchdog to reset, and enabled */
__raw_writew(0, MCFSIM_WIRR);
__raw_writew(1, MCFSIM_WRRR);
__raw_writew(0, MCFSIM_WCR);
for (;;)
/* wait for watchdog to timeout */;
}
/***************************************************************************/
void __init config_BSP(char *commandp, int size)
{
#if defined (CONFIG_MOD5272)
/* Set base of device vectors to be 64 */
writeb(0x40, MCFSIM_PIVR);
#endif
#if defined(CONFIG_NETtel) || defined(CONFIG_SCALES)
/* Copy command line from FLASH to local buffer... */
memcpy(commandp, (char *) 0xf0004000, size);
commandp[size-1] = 0;
#elif defined(CONFIG_CANCam)
/* Copy command line from FLASH to local buffer... */
memcpy(commandp, (char *) 0xf0010000, size);
commandp[size-1] = 0;
#endif
mach_reset = m5272_cpu_reset;
mach_sched_init = hw_timer_init;
}
/***************************************************************************/
/*
* Some 5272 based boards have the FEC ethernet directly connected to
* an ethernet switch. In this case we need to use the fixed phy type,
* and we need to declare it early in boot.
*/
static struct fixed_phy_status nettel_fixed_phy_status __initdata = {
.link = 1,
.speed = 100,
.duplex = 0,
};
/***************************************************************************/
static int __init init_BSP(void)
{
m5272_uarts_init();
fixed_phy_add(PHY_POLL, 0, &nettel_fixed_phy_status, -1);
return 0;
}
arch_initcall(init_BSP);
/***************************************************************************/