swh:1:snp:77163734605b0ec556b01d897b7bb4a7e30d46b6
Tip revision: 8fe28cb58bcb235034b64cbbb7550a8a43fd88be authored by Linus Torvalds on 23 December 2018, 23:55:59 UTC
Linux 4.20
Linux 4.20
Tip revision: 8fe28cb
mesh.c
// SPDX-License-Identifier: GPL-2.0
#include <linux/ieee80211.h>
#include <linux/export.h>
#include <net/cfg80211.h>
#include "nl80211.h"
#include "core.h"
#include "rdev-ops.h"
/* Default values, timeouts in ms */
#define MESH_TTL 31
#define MESH_DEFAULT_ELEMENT_TTL 31
#define MESH_MAX_RETR 3
#define MESH_RET_T 100
#define MESH_CONF_T 100
#define MESH_HOLD_T 100
#define MESH_PATH_TIMEOUT 5000
#define MESH_RANN_INTERVAL 5000
#define MESH_PATH_TO_ROOT_TIMEOUT 6000
#define MESH_ROOT_INTERVAL 5000
#define MESH_ROOT_CONFIRMATION_INTERVAL 2000
#define MESH_DEFAULT_PLINK_TIMEOUT 1800 /* timeout in seconds */
/*
* Minimum interval between two consecutive PREQs originated by the same
* interface
*/
#define MESH_PREQ_MIN_INT 10
#define MESH_PERR_MIN_INT 100
#define MESH_DIAM_TRAVERSAL_TIME 50
#define MESH_RSSI_THRESHOLD 0
/*
* A path will be refreshed if it is used PATH_REFRESH_TIME milliseconds
* before timing out. This way it will remain ACTIVE and no data frames
* will be unnecessarily held in the pending queue.
*/
#define MESH_PATH_REFRESH_TIME 1000
#define MESH_MIN_DISCOVERY_TIMEOUT (2 * MESH_DIAM_TRAVERSAL_TIME)
/* Default maximum number of established plinks per interface */
#define MESH_MAX_ESTAB_PLINKS 32
#define MESH_MAX_PREQ_RETRIES 4
#define MESH_SYNC_NEIGHBOR_OFFSET_MAX 50
#define MESH_DEFAULT_BEACON_INTERVAL 1000 /* in 1024 us units (=TUs) */
#define MESH_DEFAULT_DTIM_PERIOD 2
#define MESH_DEFAULT_AWAKE_WINDOW 10 /* in 1024 us units (=TUs) */
const struct mesh_config default_mesh_config = {
.dot11MeshRetryTimeout = MESH_RET_T,
.dot11MeshConfirmTimeout = MESH_CONF_T,
.dot11MeshHoldingTimeout = MESH_HOLD_T,
.dot11MeshMaxRetries = MESH_MAX_RETR,
.dot11MeshTTL = MESH_TTL,
.element_ttl = MESH_DEFAULT_ELEMENT_TTL,
.auto_open_plinks = true,
.dot11MeshMaxPeerLinks = MESH_MAX_ESTAB_PLINKS,
.dot11MeshNbrOffsetMaxNeighbor = MESH_SYNC_NEIGHBOR_OFFSET_MAX,
.dot11MeshHWMPactivePathTimeout = MESH_PATH_TIMEOUT,
.dot11MeshHWMPpreqMinInterval = MESH_PREQ_MIN_INT,
.dot11MeshHWMPperrMinInterval = MESH_PERR_MIN_INT,
.dot11MeshHWMPnetDiameterTraversalTime = MESH_DIAM_TRAVERSAL_TIME,
.dot11MeshHWMPmaxPREQretries = MESH_MAX_PREQ_RETRIES,
.path_refresh_time = MESH_PATH_REFRESH_TIME,
.min_discovery_timeout = MESH_MIN_DISCOVERY_TIMEOUT,
.dot11MeshHWMPRannInterval = MESH_RANN_INTERVAL,
.dot11MeshGateAnnouncementProtocol = false,
.dot11MeshForwarding = true,
.rssi_threshold = MESH_RSSI_THRESHOLD,
.ht_opmode = IEEE80211_HT_OP_MODE_PROTECTION_NONHT_MIXED,
.dot11MeshHWMPactivePathToRootTimeout = MESH_PATH_TO_ROOT_TIMEOUT,
.dot11MeshHWMProotInterval = MESH_ROOT_INTERVAL,
.dot11MeshHWMPconfirmationInterval = MESH_ROOT_CONFIRMATION_INTERVAL,
.power_mode = NL80211_MESH_POWER_ACTIVE,
.dot11MeshAwakeWindowDuration = MESH_DEFAULT_AWAKE_WINDOW,
.plink_timeout = MESH_DEFAULT_PLINK_TIMEOUT,
};
const struct mesh_setup default_mesh_setup = {
/* cfg80211_join_mesh() will pick a channel if needed */
.sync_method = IEEE80211_SYNC_METHOD_NEIGHBOR_OFFSET,
.path_sel_proto = IEEE80211_PATH_PROTOCOL_HWMP,
.path_metric = IEEE80211_PATH_METRIC_AIRTIME,
.auth_id = 0, /* open */
.ie = NULL,
.ie_len = 0,
.is_secure = false,
.user_mpm = false,
.beacon_interval = MESH_DEFAULT_BEACON_INTERVAL,
.dtim_period = MESH_DEFAULT_DTIM_PERIOD,
};
int __cfg80211_join_mesh(struct cfg80211_registered_device *rdev,
struct net_device *dev,
struct mesh_setup *setup,
const struct mesh_config *conf)
{
struct wireless_dev *wdev = dev->ieee80211_ptr;
int err;
BUILD_BUG_ON(IEEE80211_MAX_SSID_LEN != IEEE80211_MAX_MESH_ID_LEN);
ASSERT_WDEV_LOCK(wdev);
if (dev->ieee80211_ptr->iftype != NL80211_IFTYPE_MESH_POINT)
return -EOPNOTSUPP;
if (!(rdev->wiphy.flags & WIPHY_FLAG_MESH_AUTH) &&
setup->is_secure)
return -EOPNOTSUPP;
if (wdev->mesh_id_len)
return -EALREADY;
if (!setup->mesh_id_len)
return -EINVAL;
if (!rdev->ops->join_mesh)
return -EOPNOTSUPP;
if (!setup->chandef.chan) {
/* if no channel explicitly given, use preset channel */
setup->chandef = wdev->preset_chandef;
}
if (!setup->chandef.chan) {
/* if we don't have that either, use the first usable channel */
enum nl80211_band band;
for (band = 0; band < NUM_NL80211_BANDS; band++) {
struct ieee80211_supported_band *sband;
struct ieee80211_channel *chan;
int i;
sband = rdev->wiphy.bands[band];
if (!sband)
continue;
for (i = 0; i < sband->n_channels; i++) {
chan = &sband->channels[i];
if (chan->flags & (IEEE80211_CHAN_NO_IR |
IEEE80211_CHAN_DISABLED |
IEEE80211_CHAN_RADAR))
continue;
setup->chandef.chan = chan;
break;
}
if (setup->chandef.chan)
break;
}
/* no usable channel ... */
if (!setup->chandef.chan)
return -EINVAL;
setup->chandef.width = NL80211_CHAN_WIDTH_20_NOHT;
setup->chandef.center_freq1 = setup->chandef.chan->center_freq;
}
/*
* check if basic rates are available otherwise use mandatory rates as
* basic rates
*/
if (!setup->basic_rates) {
enum nl80211_bss_scan_width scan_width;
struct ieee80211_supported_band *sband =
rdev->wiphy.bands[setup->chandef.chan->band];
if (setup->chandef.chan->band == NL80211_BAND_2GHZ) {
int i;
/*
* Older versions selected the mandatory rates for
* 2.4 GHz as well, but were broken in that only
* 1 Mbps was regarded as a mandatory rate. Keep
* using just 1 Mbps as the default basic rate for
* mesh to be interoperable with older versions.
*/
for (i = 0; i < sband->n_bitrates; i++) {
if (sband->bitrates[i].bitrate == 10) {
setup->basic_rates = BIT(i);
break;
}
}
} else {
scan_width = cfg80211_chandef_to_scan_width(&setup->chandef);
setup->basic_rates = ieee80211_mandatory_rates(sband,
scan_width);
}
}
err = cfg80211_chandef_dfs_required(&rdev->wiphy,
&setup->chandef,
NL80211_IFTYPE_MESH_POINT);
if (err < 0)
return err;
if (err > 0 && !setup->userspace_handles_dfs)
return -EINVAL;
if (!cfg80211_reg_can_beacon(&rdev->wiphy, &setup->chandef,
NL80211_IFTYPE_MESH_POINT))
return -EINVAL;
err = rdev_join_mesh(rdev, dev, conf, setup);
if (!err) {
memcpy(wdev->ssid, setup->mesh_id, setup->mesh_id_len);
wdev->mesh_id_len = setup->mesh_id_len;
wdev->chandef = setup->chandef;
wdev->beacon_interval = setup->beacon_interval;
}
return err;
}
int cfg80211_set_mesh_channel(struct cfg80211_registered_device *rdev,
struct wireless_dev *wdev,
struct cfg80211_chan_def *chandef)
{
int err;
/*
* Workaround for libertas (only!), it puts the interface
* into mesh mode but doesn't implement join_mesh. Instead,
* it is configured via sysfs and then joins the mesh when
* you set the channel. Note that the libertas mesh isn't
* compatible with 802.11 mesh.
*/
if (rdev->ops->libertas_set_mesh_channel) {
if (chandef->width != NL80211_CHAN_WIDTH_20_NOHT)
return -EINVAL;
if (!netif_running(wdev->netdev))
return -ENETDOWN;
err = rdev_libertas_set_mesh_channel(rdev, wdev->netdev,
chandef->chan);
if (!err)
wdev->chandef = *chandef;
return err;
}
if (wdev->mesh_id_len)
return -EBUSY;
wdev->preset_chandef = *chandef;
return 0;
}
int __cfg80211_leave_mesh(struct cfg80211_registered_device *rdev,
struct net_device *dev)
{
struct wireless_dev *wdev = dev->ieee80211_ptr;
int err;
ASSERT_WDEV_LOCK(wdev);
if (dev->ieee80211_ptr->iftype != NL80211_IFTYPE_MESH_POINT)
return -EOPNOTSUPP;
if (!rdev->ops->leave_mesh)
return -EOPNOTSUPP;
if (!wdev->mesh_id_len)
return -ENOTCONN;
err = rdev_leave_mesh(rdev, dev);
if (!err) {
wdev->conn_owner_nlportid = 0;
wdev->mesh_id_len = 0;
wdev->beacon_interval = 0;
memset(&wdev->chandef, 0, sizeof(wdev->chandef));
rdev_set_qos_map(rdev, dev, NULL);
cfg80211_sched_dfs_chan_update(rdev);
}
return err;
}
int cfg80211_leave_mesh(struct cfg80211_registered_device *rdev,
struct net_device *dev)
{
struct wireless_dev *wdev = dev->ieee80211_ptr;
int err;
wdev_lock(wdev);
err = __cfg80211_leave_mesh(rdev, dev);
wdev_unlock(wdev);
return err;
}