swh:1:snp:c2847dfd741eae21606027cf29250d1ebcd63fb4
Tip revision: 6f7da290413ba713f0cdd9ff1a2a9bb129ef4f6c authored by Linus Torvalds on 02 July 2017, 23:07:02 UTC
Linux 4.12
Linux 4.12
Tip revision: 6f7da29
ste-href.dtsi
/*
* Copyright 2012 ST-Ericsson AB
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
#include <dt-bindings/interrupt-controller/irq.h>
#include "ste-dbx5x0.dtsi"
#include "ste-href-family-pinctrl.dtsi"
/ {
memory {
reg = <0x00000000 0x20000000>;
};
soc {
uart@80120000 {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&uart0_default_mode>;
pinctrl-1 = <&uart0_sleep_mode>;
status = "okay";
};
/* This UART is unused and thus left disabled */
uart@80121000 {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&uart1_default_mode>;
pinctrl-1 = <&uart1_sleep_mode>;
};
uart@80007000 {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&uart2_default_mode>;
pinctrl-1 = <&uart2_sleep_mode>;
status = "okay";
};
i2c@80004000 {
pinctrl-names = "default","sleep";
pinctrl-0 = <&i2c0_default_mode>;
pinctrl-1 = <&i2c0_sleep_mode>;
};
i2c@80122000 {
pinctrl-names = "default","sleep";
pinctrl-0 = <&i2c1_default_mode>;
pinctrl-1 = <&i2c1_sleep_mode>;
};
i2c@80128000 {
pinctrl-names = "default","sleep";
pinctrl-0 = <&i2c2_default_mode>;
pinctrl-1 = <&i2c2_sleep_mode>;
lp5521@33 {
compatible = "national,lp5521";
reg = <0x33>;
label = "lp5521_pri";
clock-mode = /bits/ 8 <2>;
chan0 {
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
linux,default-trigger = "heartbeat";
};
chan1 {
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
};
chan2 {
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
};
};
lp5521@34 {
compatible = "national,lp5521";
reg = <0x34>;
label = "lp5521_sec";
clock-mode = /bits/ 8 <2>;
chan0 {
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
};
chan1 {
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
};
chan2 {
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
};
};
bh1780@29 {
compatible = "rohm,bh1780gli";
reg = <0x29>;
};
};
i2c@80110000 {
pinctrl-names = "default","sleep";
pinctrl-0 = <&i2c3_default_mode>;
pinctrl-1 = <&i2c3_sleep_mode>;
};
/* ST6G3244ME level translator for 1.8/2.9 V */
vmmci: regulator-gpio {
compatible = "regulator-gpio";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2900000>;
regulator-name = "mmci-reg";
regulator-type = "voltage";
startup-delay-us = <100>;
states = <1800000 0x1
2900000 0x0>;
};
// External Micro SD slot
sdi0_per1@80126000 {
arm,primecell-periphid = <0x10480180>;
max-frequency = <100000000>;
bus-width = <4>;
cap-sd-highspeed;
cap-mmc-highspeed;
sd-uhs-sdr12;
sd-uhs-sdr25;
full-pwr-cycle;
st,sig-dir-dat0;
st,sig-dir-dat2;
st,sig-dir-cmd;
st,sig-pin-fbclk;
vmmc-supply = <&ab8500_ldo_aux3_reg>;
vqmmc-supply = <&vmmci>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdi0_default_mode>;
pinctrl-1 = <&sdi0_sleep_mode>;
status = "okay";
};
// WLAN SDIO channel
sdi1_per2@80118000 {
arm,primecell-periphid = <0x10480180>;
max-frequency = <100000000>;
bus-width = <4>;
non-removable;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdi1_default_mode>;
pinctrl-1 = <&sdi1_sleep_mode>;
status = "okay";
};
// PoP:ed eMMC
sdi2_per3@80005000 {
arm,primecell-periphid = <0x10480180>;
max-frequency = <100000000>;
bus-width = <8>;
cap-mmc-highspeed;
non-removable;
vmmc-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdi2_default_mode>;
pinctrl-1 = <&sdi2_sleep_mode>;
status = "okay";
};
// On-board eMMC
sdi4_per2@80114000 {
arm,primecell-periphid = <0x10480180>;
max-frequency = <100000000>;
bus-width = <8>;
cap-mmc-highspeed;
non-removable;
vmmc-supply = <&ab8500_ldo_aux2_reg>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdi4_default_mode>;
pinctrl-1 = <&sdi4_sleep_mode>;
status = "okay";
};
msp0: msp@80123000 {
pinctrl-names = "default";
pinctrl-0 = <&msp0_default_mode>;
status = "okay";
};
msp1: msp@80124000 {
pinctrl-names = "default";
pinctrl-0 = <&msp1_default_mode>;
status = "okay";
};
msp2: msp@80117000 {
pinctrl-names = "default";
pinctrl-0 = <&msp2_default_mode>;
};
msp3: msp@80125000 {
status = "okay";
};
prcmu@80157000 {
ab8500 {
ab8500-gpio {
};
ab8500_usb {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&musb_default_mode>;
pinctrl-1 = <&musb_sleep_mode>;
};
ab8500-regulators {
ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
regulator-name = "V-DISPLAY";
};
ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
regulator-name = "V-eMMC1";
};
ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
regulator-name = "V-MMC-SD";
};
ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
regulator-name = "V-INTCORE";
};
ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
regulator-name = "V-TVOUT";
};
ab8500_ldo_usb_reg: ab8500_ldo_usb {
regulator-name = "dummy";
};
ab8500_ldo_audio_reg: ab8500_ldo_audio {
regulator-name = "V-AUD";
};
ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
regulator-name = "V-AMIC1";
};
ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
regulator-name = "V-AMIC2";
};
ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
regulator-name = "V-DMIC";
};
ab8500_ldo_ana_reg: ab8500_ldo_ana {
regulator-name = "V-CSI/DSI";
};
};
};
};
mcde@a0350000 {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&lcd_default_mode>;
pinctrl-1 = <&lcd_sleep_mode>;
};
};
};