swh:1:snp:c2847dfd741eae21606027cf29250d1ebcd63fb4
Tip revision: 2c85ebc57b3e1817b6ce1a6b703928e113a90442 authored by Linus Torvalds on 13 December 2020, 22:41:30 UTC
Linux 5.10
Linux 5.10
Tip revision: 2c85ebc
Kconfig
# SPDX-License-Identifier: GPL-2.0-only
menuconfig ARCH_AT91
bool "AT91/Microchip SoCs"
depends on ARCH_MULTI_V4T || ARCH_MULTI_V5 || ARCH_MULTI_V7 || ARM_SINGLE_ARMV7M
select ARM_CPU_SUSPEND if PM && ARCH_MULTI_V7
select COMMON_CLK_AT91
select GPIOLIB
select PINCTRL
select SOC_BUS
if ARCH_AT91
config SOC_SAMV7
bool "SAM Cortex-M7 family" if ARM_SINGLE_ARMV7M
select COMMON_CLK_AT91
select PINCTRL_AT91
help
Select this if you are using an SoC from Microchip's SAME7, SAMS7 or SAMV7
families.
config SOC_SAMA5D2
bool "SAMA5D2 family"
depends on ARCH_MULTI_V7
select SOC_SAMA5
select CACHE_L2X0
select HAVE_AT91_UTMI
select HAVE_AT91_USB_CLK
select HAVE_AT91_H32MX
select HAVE_AT91_GENERATED_CLK
select HAVE_AT91_AUDIO_PLL
select HAVE_AT91_I2S_MUX_CLK
select PINCTRL_AT91PIO4
help
Select this if ou are using one of Microchip's SAMA5D2 family SoC.
config SOC_SAMA5D3
bool "SAMA5D3 family"
depends on ARCH_MULTI_V7
select SOC_SAMA5
select HAVE_AT91_UTMI
select HAVE_AT91_SMD
select HAVE_AT91_USB_CLK
select PINCTRL_AT91
help
Select this if you are using one of Microchip's SAMA5D3 family SoC.
This support covers SAMA5D31, SAMA5D33, SAMA5D34, SAMA5D35, SAMA5D36.
config SOC_SAMA5D4
bool "SAMA5D4 family"
depends on ARCH_MULTI_V7
select SOC_SAMA5
select CACHE_L2X0
select HAVE_AT91_UTMI
select HAVE_AT91_SMD
select HAVE_AT91_USB_CLK
select HAVE_AT91_H32MX
select PINCTRL_AT91
help
Select this if you are using one of Microchip's SAMA5D4 family SoC.
config SOC_AT91RM9200
bool "AT91RM9200"
depends on ARCH_MULTI_V4T
select ATMEL_AIC_IRQ
select ATMEL_PM if PM
select ATMEL_ST
select CPU_ARM920T
select HAVE_AT91_USB_CLK
select PINCTRL_AT91
select SOC_SAM_V4_V5
select SRAM if PM
help
Select this if you are using Microchip's AT91RM9200 SoC.
config SOC_AT91SAM9
bool "AT91SAM9"
depends on ARCH_MULTI_V5
select ATMEL_AIC_IRQ
select ATMEL_PM if PM
select ATMEL_SDRAMC
select CPU_ARM926T
select HAVE_AT91_SMD
select HAVE_AT91_USB_CLK
select HAVE_AT91_UTMI
select HAVE_FB_ATMEL
select MEMORY
select PINCTRL_AT91
select SOC_SAM_V4_V5
select SRAM if PM
help
Select this if you are using one of those Microchip SoC:
AT91SAM9260
AT91SAM9261
AT91SAM9263
AT91SAM9G15
AT91SAM9G20
AT91SAM9G25
AT91SAM9G35
AT91SAM9G45
AT91SAM9G46
AT91SAM9M10
AT91SAM9M11
AT91SAM9N12
AT91SAM9RL
AT91SAM9X25
AT91SAM9X35
AT91SAM9XE
config SOC_SAM9X60
bool "SAM9X60"
depends on ARCH_MULTI_V5
select ATMEL_AIC5_IRQ
select ATMEL_PM if PM
select ATMEL_SDRAMC
select CPU_ARM926T
select HAVE_AT91_USB_CLK
select HAVE_AT91_GENERATED_CLK
select HAVE_AT91_SAM9X60_PLL
select MEMORY
select PINCTRL_AT91
select SOC_SAM_V4_V5
select SRAM if PM
help
Select this if you are using Microchip's SAM9X60 SoC
comment "Clocksource driver selection"
config ATMEL_CLOCKSOURCE_PIT
bool "Periodic Interval Timer (PIT) support"
depends on SOC_AT91SAM9 || SOC_SAM9X60 || SOC_SAMA5
default SOC_AT91SAM9 || SOC_SAMA5
select ATMEL_PIT
help
Select this to get a clocksource based on the Atmel Periodic Interval
Timer. It has a relatively low resolution and the TC Block clocksource
should be preferred.
config ATMEL_CLOCKSOURCE_TCB
bool "Timer Counter Blocks (TCB) support"
default SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAM9X60 || SOC_SAMA5
select ATMEL_TCB_CLKSRC
help
Select this to get a high precision clocksource based on a
TC block with a 5+ MHz base clock rate.
On platforms with 16-bit counters, two timer channels are combined
to make a single 32-bit timer.
It can also be used as a clock event device supporting oneshot mode.
config HAVE_AT91_UTMI
bool
config HAVE_AT91_USB_CLK
bool
config COMMON_CLK_AT91
bool
select MFD_SYSCON
config HAVE_AT91_SMD
bool
config HAVE_AT91_H32MX
bool
config HAVE_AT91_GENERATED_CLK
bool
config HAVE_AT91_AUDIO_PLL
bool
config HAVE_AT91_I2S_MUX_CLK
bool
config HAVE_AT91_SAM9X60_PLL
bool
config SOC_SAM_V4_V5
bool
config SOC_SAM_V7
bool
config SOC_SAMA5
bool
select ATMEL_AIC5_IRQ
select ATMEL_PM if PM
select ATMEL_SDRAMC
select MEMORY
select SOC_SAM_V7
select SRAM if PM
config ATMEL_PM
bool
endif