swh:1:snp:c2847dfd741eae21606027cf29250d1ebcd63fb4
Tip revision: 4cbe5a555fa58a79b6ecbb6c531b8bab0650778d authored by Linus Torvalds on 01 September 2012, 17:39:58 UTC
Linux 3.6-rc4
Linux 3.6-rc4
Tip revision: 4cbe5a5
devices.c
/*
* linux/arch/arm/plat-omap/devices.c
*
* Common platform device setup/initialization for OMAP1 and OMAP2
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/slab.h>
#include <linux/memblock.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <asm/memblock.h>
#include <plat/tc.h>
#include <plat/board.h>
#include <plat/mmc.h>
#include <plat/menelaus.h>
#include <plat/omap44xx.h>
/*-------------------------------------------------------------------------*/
#if defined(CONFIG_HW_RANDOM_OMAP) || defined(CONFIG_HW_RANDOM_OMAP_MODULE)
#ifdef CONFIG_ARCH_OMAP2
#define OMAP_RNG_BASE 0x480A0000
#else
#define OMAP_RNG_BASE 0xfffe5000
#endif
static struct resource rng_resources[] = {
{
.start = OMAP_RNG_BASE,
.end = OMAP_RNG_BASE + 0x4f,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device omap_rng_device = {
.name = "omap_rng",
.id = -1,
.num_resources = ARRAY_SIZE(rng_resources),
.resource = rng_resources,
};
static void omap_init_rng(void)
{
(void) platform_device_register(&omap_rng_device);
}
#else
static inline void omap_init_rng(void) {}
#endif
/*
* This gets called after board-specific INIT_MACHINE, and initializes most
* on-chip peripherals accessible on this board (except for few like USB):
*
* (a) Does any "standard config" pin muxing needed. Board-specific
* code will have muxed GPIO pins and done "nonstandard" setup;
* that code could live in the boot loader.
* (b) Populating board-specific platform_data with the data drivers
* rely on to handle wiring variations.
* (c) Creating platform devices as meaningful on this board and
* with this kernel configuration.
*
* Claiming GPIOs, and setting their direction and initial values, is the
* responsibility of the device drivers. So is responding to probe().
*
* Board-specific knowledge like creating devices or pin setup is to be
* kept out of drivers as much as possible. In particular, pin setup
* may be handled by the boot loader, and drivers should expect it will
* normally have been done by the time they're probed.
*/
static int __init omap_init_devices(void)
{
/* please keep these calls, and their implementations above,
* in alphabetical order so they're easier to sort through.
*/
omap_init_rng();
return 0;
}
arch_initcall(omap_init_devices);