swh:1:snp:c2847dfd741eae21606027cf29250d1ebcd63fb4
Tip revision: 6efb943b8616ec53a5e444193dccf1af9ad627b5 authored by Linus Torvalds on 09 May 2021, 21:17:44 UTC
Linux 5.13-rc1
Linux 5.13-rc1
Tip revision: 6efb943
head.S
/* SPDX-License-Identifier: GPL-2.0 */
/*
* head.S - Common startup code for 68000 core based CPU's
*
* 2012.10.21, Luis Alves <ljalvs@gmail.com>, Single head.S file for all
* 68000 core based CPU's. Based on the sources from:
* Coldfire by Greg Ungerer <gerg@snapgear.com>
* 68328 by D. Jeff Dionne <jeff@ryeham.ee.ryerson.ca>,
* Kenneth Albanowski <kjahds@kjahds.com>,
* The Silver Hammer Group, Ltd.
*
*/
#include <linux/linkage.h>
#include <linux/init.h>
#include <asm/asm-offsets.h>
#include <asm/thread_info.h>
/*****************************************************************************
* UCSIMM and UCDIMM use CONFIG_MEMORY_RESERVE to reserve some RAM
*****************************************************************************/
#ifdef CONFIG_MEMORY_RESERVE
#define RAMEND (CONFIG_RAMBASE+CONFIG_RAMSIZE)-(CONFIG_MEMORY_RESERVE*0x100000)
#else
#define RAMEND (CONFIG_RAMBASE+CONFIG_RAMSIZE)
#endif
/*****************************************************************************/
.global _start
.global _rambase
.global _ramvec
.global _ramstart
.global _ramend
#if defined(CONFIG_PILOT) || defined(CONFIG_INIT_LCD)
.global bootlogo_bits
#endif
/* Defining DEBUG_HEAD_CODE, serial port in 68x328 is inited */
/* #define DEBUG_HEAD_CODE */
#undef DEBUG_HEAD_CODE
.data
/*****************************************************************************
* RAM setup pointers. Used by the kernel to determine RAM location and size.
*****************************************************************************/
_rambase:
.long 0
_ramvec:
.long 0
_ramstart:
.long 0
_ramend:
.long 0
__HEAD
/*****************************************************************************
* Entry point, where all begins!
*****************************************************************************/
_start:
/* Pilot need this specific signature at the start of ROM */
#ifdef CONFIG_PILOT
.byte 0x4e, 0xfa, 0x00, 0x0a /* bra opcode (jmp 10 bytes) */
.byte 'b', 'o', 'o', 't'
.word 10000
nop
moveq #0, %d0
movew %d0, 0xfffff618 /* Watchdog off */
movel #0x00011f07, 0xfffff114 /* CS A1 Mask */
#endif /* CONFIG_PILOT */
movew #0x2700, %sr /* disable all interrupts */
/*****************************************************************************
* Setup PLL and wait for it to settle (in 68x328 cpu's).
* Also, if enabled, init serial port.
*****************************************************************************/
#if defined(CONFIG_M68328) || \
defined(CONFIG_M68EZ328) || \
defined(CONFIG_M68VZ328)
/* Serial port setup. Should only be needed if debugging this startup code. */
#ifdef DEBUG_HEAD_CODE
movew #0x0800, 0xfffff906 /* Ignore CTS */
movew #0x010b, 0xfffff902 /* BAUD to 9600 */
movew #0xe100, 0xfffff900 /* enable */
#endif /* DEBUG_HEAD */
#ifdef CONFIG_PILOT
movew #0x2410, 0xfffff200 /* PLLCR */
#else
movew #0x2400, 0xfffff200 /* PLLCR */
#endif
movew #0x0123, 0xfffff202 /* PLLFSR */
moveq #0, %d0
movew #16384, %d0 /* PLL settle wait loop */
_pll_settle:
subw #1, %d0
bne _pll_settle
#endif /* CONFIG_M68x328 */
/*****************************************************************************
* If running kernel from ROM some specific initialization has to be done.
* (Assuming that everything is already init'ed when running from RAM)
*****************************************************************************/
#ifdef CONFIG_ROMKERNEL
/*****************************************************************************
* Init chip registers (uCsimm specific)
*****************************************************************************/
#ifdef CONFIG_UCSIMM
moveb #0x00, 0xfffffb0b /* Watchdog off */
moveb #0x10, 0xfffff000 /* SCR */
moveb #0x00, 0xfffff40b /* enable chip select */
moveb #0x00, 0xfffff423 /* enable /DWE */
moveb #0x08, 0xfffffd0d /* disable hardmap */
moveb #0x07, 0xfffffd0e /* level 7 interrupt clear */
movew #0x8600, 0xfffff100 /* FLASH at 0x10c00000 */
movew #0x018b, 0xfffff110 /* 2Meg, enable, 0ws */
movew #0x8f00, 0xfffffc00 /* DRAM configuration */
movew #0x9667, 0xfffffc02 /* DRAM control */
movew #0x0000, 0xfffff106 /* DRAM at 0x00000000 */
movew #0x068f, 0xfffff116 /* 8Meg, enable, 0ws */
moveb #0x40, 0xfffff300 /* IVR */
movel #0x007FFFFF, %d0 /* IMR */
movel %d0, 0xfffff304
moveb 0xfffff42b, %d0
andb #0xe0, %d0
moveb %d0, 0xfffff42b
#endif
/*****************************************************************************
* Init LCD controller.
* (Assuming that LCD controller is already init'ed when running from RAM)
*****************************************************************************/
#ifdef CONFIG_INIT_LCD
#ifdef CONFIG_PILOT
moveb #0, 0xfffffA27 /* LCKCON */
movel #_start, 0xfffffA00 /* LSSA */
moveb #0xa, 0xfffffA05 /* LVPW */
movew #0x9f, 0xFFFFFa08 /* LXMAX */
movew #0x9f, 0xFFFFFa0a /* LYMAX */
moveb #9, 0xfffffa29 /* LBAR */
moveb #0, 0xfffffa25 /* LPXCD */
moveb #0x04, 0xFFFFFa20 /* LPICF */
moveb #0x58, 0xfffffA27 /* LCKCON */
moveb #0x85, 0xfffff429 /* PFDATA */
moveb #0xd8, 0xfffffA27 /* LCKCON */
moveb #0xc5, 0xfffff429 /* PFDATA */
moveb #0xd5, 0xfffff429 /* PFDATA */
movel #bootlogo_bits, 0xFFFFFA00 /* LSSA */
moveb #10, 0xFFFFFA05 /* LVPW */
movew #160, 0xFFFFFA08 /* LXMAX */
movew #160, 0xFFFFFA0A /* LYMAX */
#else /* CONFIG_PILOT */
movel #bootlogo_bits, 0xfffffA00 /* LSSA */
moveb #0x28, 0xfffffA05 /* LVPW */
movew #0x280, 0xFFFFFa08 /* LXMAX */
movew #0x1df, 0xFFFFFa0a /* LYMAX */
moveb #0, 0xfffffa29 /* LBAR */
moveb #0, 0xfffffa25 /* LPXCD */
moveb #0x08, 0xFFFFFa20 /* LPICF */
moveb #0x01, 0xFFFFFA21 /* -ve pol */
moveb #0x81, 0xfffffA27 /* LCKCON */
movew #0xff00, 0xfffff412 /* LCD pins */
#endif /* CONFIG_PILOT */
#endif /* CONFIG_INIT_LCD */
/*****************************************************************************
* Kernel is running from FLASH/ROM (XIP)
* Copy init text & data to RAM
*****************************************************************************/
moveal #_etext, %a0
moveal #_sdata, %a1
moveal #__bss_start, %a2
_copy_initmem:
movel %a0@+, %a1@+
cmpal %a1, %a2
bhi _copy_initmem
#endif /* CONFIG_ROMKERNEL */
/*****************************************************************************
* Setup basic memory information for kernel
*****************************************************************************/
movel #CONFIG_VECTORBASE,_ramvec /* set vector base location */
movel #CONFIG_RAMBASE,_rambase /* set the base of RAM */
movel #RAMEND, _ramend /* set end ram addr */
lea __bss_stop,%a1
movel %a1,_ramstart
/*****************************************************************************
* If the kernel is in RAM, move romfs to right above bss and
* adjust _ramstart to where romfs ends.
*
* (Do this only if CONFIG_MTD_UCLINUX is true)
*****************************************************************************/
#if defined(CONFIG_ROMFS_FS) && defined(CONFIG_RAMKERNEL) && \
defined(CONFIG_MTD_UCLINUX)
lea __bss_start, %a0 /* get start of bss */
lea __bss_stop, %a1 /* set up destination */
movel %a0, %a2 /* copy of bss start */
movel 8(%a0), %d0 /* get size of ROMFS */
addql #8, %d0 /* allow for rounding */
andl #0xfffffffc, %d0 /* whole words */
addl %d0, %a0 /* copy from end */
addl %d0, %a1 /* copy from end */
movel %a1, _ramstart /* set start of ram */
_copy_romfs:
movel -(%a0), -(%a1) /* copy dword */
cmpl %a0, %a2 /* check if at end */
bne _copy_romfs
#endif /* CONFIG_ROMFS_FS && CONFIG_RAMKERNEL && CONFIG_MTD_UCLINUX */
/*****************************************************************************
* Clear bss region
*****************************************************************************/
lea __bss_start, %a0 /* get start of bss */
lea __bss_stop, %a1 /* get end of bss */
_clear_bss:
movel #0, (%a0)+ /* clear each word */
cmpl %a0, %a1 /* check if at end */
bne _clear_bss
/*****************************************************************************
* Load the current task pointer and stack.
*****************************************************************************/
lea init_thread_union,%a0
lea THREAD_SIZE(%a0),%sp
jsr start_kernel /* start Linux kernel */
_exit:
jmp _exit /* should never get here */