swh:1:snp:c3bf2749e3476071fa748f67b0ffa2fdc5fe49d9
Tip revision: 3c0eee3fe6a3a1c745379547c7e7c904aa64f6d5 authored by Linus Torvalds on 05 January 2011, 00:50:19 UTC
Linux 2.6.37
Linux 2.6.37
Tip revision: 3c0eee3
fsmc.h
/*
* incude/mtd/fsmc.h
*
* ST Microelectronics
* Flexible Static Memory Controller (FSMC)
* platform data interface and header file
*
* Copyright © 2010 ST Microelectronics
* Vipin Kumar <vipin.kumar@st.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#ifndef __MTD_FSMC_H
#define __MTD_FSMC_H
#include <linux/platform_device.h>
#include <linux/mtd/physmap.h>
#include <linux/types.h>
#include <linux/mtd/partitions.h>
#include <asm/param.h>
#define FSMC_NAND_BW8 1
#define FSMC_NAND_BW16 2
/*
* The placement of the Command Latch Enable (CLE) and
* Address Latch Enable (ALE) is twised around in the
* SPEAR310 implementation.
*/
#if defined(CONFIG_MACH_SPEAR310)
#define PLAT_NAND_CLE (1 << 17)
#define PLAT_NAND_ALE (1 << 16)
#else
#define PLAT_NAND_CLE (1 << 16)
#define PLAT_NAND_ALE (1 << 17)
#endif
#define FSMC_MAX_NOR_BANKS 4
#define FSMC_MAX_NAND_BANKS 4
#define FSMC_FLASH_WIDTH8 1
#define FSMC_FLASH_WIDTH16 2
struct fsmc_nor_bank_regs {
uint32_t ctrl;
uint32_t ctrl_tim;
};
/* ctrl register definitions */
#define BANK_ENABLE (1 << 0)
#define MUXED (1 << 1)
#define NOR_DEV (2 << 2)
#define WIDTH_8 (0 << 4)
#define WIDTH_16 (1 << 4)
#define RSTPWRDWN (1 << 6)
#define WPROT (1 << 7)
#define WRT_ENABLE (1 << 12)
#define WAIT_ENB (1 << 13)
/* ctrl_tim register definitions */
struct fsms_nand_bank_regs {
uint32_t pc;
uint32_t sts;
uint32_t comm;
uint32_t attrib;
uint32_t ioata;
uint32_t ecc1;
uint32_t ecc2;
uint32_t ecc3;
};
#define FSMC_NOR_REG_SIZE 0x40
struct fsmc_regs {
struct fsmc_nor_bank_regs nor_bank_regs[FSMC_MAX_NOR_BANKS];
uint8_t reserved_1[0x40 - 0x20];
struct fsms_nand_bank_regs bank_regs[FSMC_MAX_NAND_BANKS];
uint8_t reserved_2[0xfe0 - 0xc0];
uint32_t peripid0; /* 0xfe0 */
uint32_t peripid1; /* 0xfe4 */
uint32_t peripid2; /* 0xfe8 */
uint32_t peripid3; /* 0xfec */
uint32_t pcellid0; /* 0xff0 */
uint32_t pcellid1; /* 0xff4 */
uint32_t pcellid2; /* 0xff8 */
uint32_t pcellid3; /* 0xffc */
};
#define FSMC_BUSY_WAIT_TIMEOUT (1 * HZ)
/* pc register definitions */
#define FSMC_RESET (1 << 0)
#define FSMC_WAITON (1 << 1)
#define FSMC_ENABLE (1 << 2)
#define FSMC_DEVTYPE_NAND (1 << 3)
#define FSMC_DEVWID_8 (0 << 4)
#define FSMC_DEVWID_16 (1 << 4)
#define FSMC_ECCEN (1 << 6)
#define FSMC_ECCPLEN_512 (0 << 7)
#define FSMC_ECCPLEN_256 (1 << 7)
#define FSMC_TCLR_1 (1 << 9)
#define FSMC_TAR_1 (1 << 13)
/* sts register definitions */
#define FSMC_CODE_RDY (1 << 15)
/* comm register definitions */
#define FSMC_TSET_0 (0 << 0)
#define FSMC_TWAIT_6 (6 << 8)
#define FSMC_THOLD_4 (4 << 16)
#define FSMC_THIZ_1 (1 << 24)
/* peripid2 register definitions */
#define FSMC_REVISION_MSK (0xf)
#define FSMC_REVISION_SHFT (0x4)
#define FSMC_VER1 1
#define FSMC_VER2 2
#define FSMC_VER3 3
#define FSMC_VER4 4
#define FSMC_VER5 5
#define FSMC_VER6 6
#define FSMC_VER7 7
#define FSMC_VER8 8
static inline uint32_t get_fsmc_version(struct fsmc_regs *regs)
{
return (readl(®s->peripid2) >> FSMC_REVISION_SHFT) &
FSMC_REVISION_MSK;
}
/*
* There are 13 bytes of ecc for every 512 byte block in FSMC version 8
* and it has to be read consecutively and immediately after the 512
* byte data block for hardware to generate the error bit offsets
* Managing the ecc bytes in the following way is easier. This way is
* similar to oobfree structure maintained already in u-boot nand driver
*/
#define MAX_ECCPLACE_ENTRIES 32
struct fsmc_nand_eccplace {
uint8_t offset;
uint8_t length;
};
struct fsmc_eccplace {
struct fsmc_nand_eccplace eccplace[MAX_ECCPLACE_ENTRIES];
};
/**
* fsmc_nand_platform_data - platform specific NAND controller config
* @partitions: partition table for the platform, use a default fallback
* if this is NULL
* @nr_partitions: the number of partitions in the previous entry
* @options: different options for the driver
* @width: bus width
* @bank: default bank
* @select_bank: callback to select a certain bank, this is
* platform-specific. If the controller only supports one bank
* this may be set to NULL
*/
struct fsmc_nand_platform_data {
struct mtd_partition *partitions;
unsigned int nr_partitions;
unsigned int options;
unsigned int width;
unsigned int bank;
void (*select_bank)(uint32_t bank, uint32_t busw);
};
extern int __init fsmc_nor_init(struct platform_device *pdev,
unsigned long base, uint32_t bank, uint32_t width);
extern void __init fsmc_init_board_info(struct platform_device *pdev,
struct mtd_partition *partitions, unsigned int nr_partitions,
unsigned int width);
#endif /* __MTD_FSMC_H */