#
# USB Dual Role (OTG-ready) Controller Drivers
# for silicon based on Mentor Graphics INVENTRA designs
#
# (M)HDRC = (Multipoint) Highspeed Dual-Role Controller
config USB_MUSB_HDRC
tristate 'Inventra Highspeed Dual Role Controller (TI, ADI, ...)'
depends on USB && USB_GADGET
select NOP_USB_XCEIV if (ARCH_DAVINCI || MACH_OMAP3EVM || BLACKFIN)
select NOP_USB_XCEIV if (SOC_TI81XX || SOC_AM33XX)
select TWL4030_USB if MACH_OMAP_3430SDP
select TWL6030_USB if MACH_OMAP_4430SDP || MACH_OMAP4_PANDA
select USB_OTG_UTILS
select USB_GADGET_DUALSPEED
help
Say Y here if your system has a dual role high speed USB
controller based on the Mentor Graphics silicon IP. Then
configure options to match your silicon and the board
it's being used with, including the USB peripheral role,
or the USB host role, or both.
Texas Instruments familiies using this IP include DaVinci
(35x, 644x ...), OMAP 243x, OMAP 3, and TUSB 6010.
Analog Devices parts using this IP include Blackfin BF54x,
BF525 and BF527.
If you do not know what this is, please say N.
To compile this driver as a module, choose M here; the
module will be called "musb-hdrc".
if USB_MUSB_HDRC
choice
prompt "Platform Glue Layer"
config USB_MUSB_DAVINCI
tristate "DaVinci"
depends on ARCH_DAVINCI_DMx
config USB_MUSB_DA8XX
tristate "DA8xx/OMAP-L1x"
depends on ARCH_DAVINCI_DA8XX
config USB_MUSB_TUSB6010
tristate "TUSB6010"
config USB_MUSB_OMAP2PLUS
tristate "OMAP2430 and onwards"
depends on ARCH_OMAP2PLUS
config USB_MUSB_AM35X
tristate "AM35x"
depends on ARCH_OMAP
config USB_MUSB_DSPS
tristate "TI DSPS platforms"
depends on SOC_TI81XX || SOC_AM33XX
config USB_MUSB_BLACKFIN
tristate "Blackfin"
depends on (BF54x && !BF544) || (BF52x && ! BF522 && !BF523)
config USB_MUSB_UX500
tristate "U8500 and U5500"
depends on (ARCH_U8500 && AB8500_USB)
endchoice
choice
prompt 'MUSB DMA mode'
default USB_UX500_DMA if USB_MUSB_UX500
default USB_INVENTRA_DMA if USB_MUSB_OMAP2PLUS || USB_MUSB_BLACKFIN
default USB_TI_CPPI_DMA if USB_MUSB_DAVINCI
default USB_TUSB_OMAP_DMA if USB_MUSB_TUSB6010
default MUSB_PIO_ONLY if USB_MUSB_TUSB6010 || USB_MUSB_DA8XX || USB_MUSB_AM35X \
|| USB_MUSB_DSPS
help
Unfortunately, only one option can be enabled here. Ideally one
should be able to build all these drivers into one kernel to
allow using DMA on multiplatform kernels.
config USB_UX500_DMA
bool 'ST Ericsson U8500 and U5500'
depends on USB_MUSB_UX500
help
Enable DMA transfers on UX500 platforms.
config USB_INVENTRA_DMA
bool 'Inventra'
depends on USB_MUSB_OMAP2PLUS || USB_MUSB_BLACKFIN
help
Enable DMA transfers using Mentor's engine.
config USB_TI_CPPI_DMA
bool 'TI CPPI (Davinci)'
depends on USB_MUSB_DAVINCI
help
Enable DMA transfers when TI CPPI DMA is available.
config USB_TUSB_OMAP_DMA
bool 'TUSB 6010'
depends on USB_MUSB_TUSB6010
depends on ARCH_OMAP
help
Enable DMA transfers on TUSB 6010 when OMAP DMA is available.
config MUSB_PIO_ONLY
bool 'Disable DMA (always use PIO)'
help
All data is copied between memory and FIFO by the CPU.
DMA controllers are ignored.
Do not choose this unless DMA support for your SOC or board
is unavailable (or unstable). When DMA is enabled at compile time,
you can still disable it at run time using the "use_dma=n" module
parameter.
endchoice
endif # USB_MUSB_HDRC