Revision 4dda864d73079a1eb01fab4ec29b97db150163bf authored by Geert Uytterhoeven on 28 October 2016, 12:07:47 UTC, committed by Greg Kroah-Hartman on 28 October 2016, 12:13:07 UTC
The port->console flag is always false, as uart_console() is called before the serial console has been registered. Hence for a serial port used as the console, uart_tty_port_shutdown() will still be called when userspace closes the port, powering it down. This may lead to a system lock up when the serial console driver writes to the serial port's registers. To fix this, move the setting of port->console after the call to uart_configure_port(), which registers the serial console. Fixes: 761ed4a94582ab29 ("tty: serial_core: convert uart_close to use tty_port_close") Reported-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Rob Herring <robh@kernel.org> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> [robh: rebased on tty-linus] Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1 parent 9bcffe7
File | Mode | Size |
---|---|---|
accessibility | ||
acpi | ||
amba | ||
android | ||
ata | ||
atm | ||
auxdisplay | ||
base | ||
bcma | ||
block | ||
bluetooth | ||
bus | ||
cdrom | ||
char | ||
clk | ||
clocksource | ||
connector | ||
cpufreq | ||
cpuidle | ||
crypto | ||
dax | ||
dca | ||
devfreq | ||
dio | ||
dma | ||
dma-buf | ||
edac | ||
eisa | ||
extcon | ||
firewire | ||
firmware | ||
fmc | ||
fpga | ||
gpio | ||
gpu | ||
hid | ||
hsi | ||
hv | ||
hwmon | ||
hwspinlock | ||
hwtracing | ||
i2c | ||
ide | ||
idle | ||
iio | ||
infiniband | ||
input | ||
iommu | ||
ipack | ||
irqchip | ||
isdn | ||
leds | ||
lguest | ||
lightnvm | ||
macintosh | ||
mailbox | ||
mcb | ||
md | ||
media | ||
memory | ||
memstick | ||
message | ||
mfd | ||
misc | ||
mmc | ||
mtd | ||
net | ||
nfc | ||
ntb | ||
nubus | ||
nvdimm | ||
nvme | ||
nvmem | ||
of | ||
oprofile | ||
parisc | ||
parport | ||
pci | ||
pcmcia | ||
perf | ||
phy | ||
pinctrl | ||
platform | ||
pnp | ||
power | ||
powercap | ||
pps | ||
ps3 | ||
ptp | ||
pwm | ||
rapidio | ||
ras | ||
regulator | ||
remoteproc | ||
reset | ||
rpmsg | ||
rtc | ||
s390 | ||
sbus | ||
scsi | ||
sfi | ||
sh | ||
sn | ||
soc | ||
spi | ||
spmi | ||
ssb | ||
staging | ||
target | ||
tc | ||
thermal | ||
thunderbolt | ||
tty | ||
uio | ||
usb | ||
uwb | ||
vfio | ||
vhost | ||
video | ||
virt | ||
virtio | ||
vlynq | ||
vme | ||
w1 | ||
watchdog | ||
xen | ||
zorro | ||
Kconfig | -rw-r--r-- | 3.3 KB |
Makefile | -rw-r--r-- | 4.9 KB |
Computing file changes ...